iCAx开思网

标题: 【原创】看我的五轴 [打印本页]

作者: hchhyl    时间: 2004-5-1 12:07
标题: 【原创】看我的五轴
1
作者: hchhyl    时间: 2004-5-1 12:08
2
作者: hchhyl    时间: 2004-5-1 12:09
3
作者: hchhyl    时间: 2004-5-1 12:10
4
作者: hchhyl    时间: 2004-5-1 12:10
5
作者: hchhyl    时间: 2004-5-1 12:11
6
作者: hchhyl    时间: 2004-5-1 12:12
7
作者: hchhyl    时间: 2004-5-1 12:13
8
作者: hchhyl    时间: 2004-5-1 12:13
9
作者: hchhyl    时间: 2004-5-1 12:17
%
N0010 G40 G17 G94 G90 G54
(PartName='E:\hch\tk14_089_mech_1.prt' GenerateDate=Wed Apr 28 10:34:23 2004)
(ToolNumber=2 ToolRegister=0)
(ToolName=MILL_10_FLAT Diameter=10.00 Radius=0.00 Flute Length=50.00 Length=75.00)
(UG Version:Unigraphics NX 2.0.0.21)
N0020 M54
N0030 G91 G30 Z0.0
N0040 T02 M06
N0050 M54
N0060 G57
N0070 G00 G90 X.001 Y266.275 Z377.181 A-44.774 C84.485 S2000
N0080 G43 H01
N0090 Z329.981
N0100 G01 Z326.981 F300. M08
N0110 X-.001 Y266.346 Z326.976 A-44.785 C84.488 F500.
N0120 X.001 Y266.91 Z326.935 A-44.873 C84.504
N0130 Y267.616 Z326.882 A-44.983 C84.525
N0140 Z329.882 F800.
N0150 G00 Z337.082
N0160 X.06 Y265.452 Z337.203 A-44.723 C84.933
N0170 X.114 Y263.302 Z337.313 A-44.465 C85.345
N0180 Z330.117
N0190 G01 X0.0 Y264.296 Z327.117 F300.
N0200 Y264.437 Z327.108 A-44.487 C85.349 F500.
N0210 Y264.719 Z327.089 A-44.531 C85.356
N0220 Y265.283 Z327.05 A-44.619 C85.37
N0230 X-.001 Y266.403 Z326.971 A-44.794 C85.399
N0240 X.001 Y267.672 Z326.878 A-44.992 C85.43
N0250 Z329.878 F800.
N0260 G00 Z337.078
N0270 X.049 Y264.476 Z337.271 A-44.571 C85.822
N0280 X.091 Y261.284 Z337.441 A-44.151 C86.221
N0290 Z330.245
N0300 G01 X-.001 Y262.28 Z327.245 F300.
N0310 X0.0 Y262.32 Z327.242 A-44.157 F500.
N0320 Y262.602 Z327.225 A-44.201 C86.227
N0330 Y263.73 Z327.154 A-44.377 C86.25
N0340 Y265.994 Z327.001 A-44.73 C86.296
N0350 (A=-45.01599999999999800)
N0360 Y267.826 Z326.866 A-45. C86.333
N0370 (A=-45.01599999999999800)
N0380 Z329.866 F800.
N0390 (A=-45.01599999999999800)
N0400 G00 Z337.066
N0410 X.038 Y263.571 Z337.331 A-44.43 C86.719
N0420 X.069 Y259.327 Z337.555 A-43.846 C87.114
N0430 Z330.358
N0440 G01 X-.001 Y260.325 Z327.358 F300.
N0450 X0.0 Y260.356 Z327.357 A-43.851 F500.
N0460 Y260.426 Z327.353 A-43.862 C87.115
N0470 X.001 Y260.567 Z327.345 A-43.884 C87.117
N0480 Y261.14 Z327.312 A-43.973 C87.126
N0490 (A=-45.00999999999999800)
N0500 X0.0 Y267.787 Z326.869 A-45. C87.229
N0510 (A=-45.00999999999999800)
N0520 Z329.869 F800.
N0530 (A=-45.00999999999999800)
N0540 G00 X-.001 Z337.069
N0550 X.027 Y262.584 Z337.394 A-44.276 C87.621
N0560 X.048 Y257.382 Z337.657 A-43.543 C88.024
N0570 Z330.461
N0580 G01 X.001 Y258.381 Z327.461 F300.
N0590 X0.0 Y258.411 Z327.459 A-43.548 C88.025 F500.
N0600 X.001 Y258.482 Z327.456 A-43.559
N0610 X0.0 Y258.632 Z327.448 A-43.582 C88.027
N0620 Y260.895 Z327.326 A-43.935 C88.051
N0630 Y265.437 Z327.04 A-44.643 C88.099
N0640 (A=-45.01800000000000800)
N0650 X-.001 Y267.839 Z326.865 A-45. C88.124
N0660 (A=-45.01800000000000800)
N0670 Z329.865 F800.
N0680 (A=-45.01800000000000800)
N0690 G00 Z337.065
N0700 X.015 Y261.607 Z337.454 A-44.124 C88.532
N0710 X.025 Y255.385 Z337.752 A-43.232 C88.953
N0720 Z330.555
N0730 G01 X0.0 Y256.384 Z327.555 F300.
N0740 Y256.415 Z327.554 A-43.237 F500.
N0750 X-.001 Y256.486 Z327.551 A-43.248 C88.954
N0760 X0.0 Y256.776 Z327.538 A-43.293 C88.955
N0770 X.001 Y257.34 Z327.511 A-43.381 C88.958
N0780 X0.0 Y258.476 Z327.456 A-43.558 C88.965
N0790 X-.001 Y260.748 Z327.335 A-43.912 C88.978
N0800 Y265.289 Z327.05 A-44.62 C89.003
N0810 X0.0 Y267.558 Z326.887 A-44.974 C89.015
N0820 X-.001 Y267.698 Z326.876 A-44.996 C89.016
N0830 Z329.876 F800.
N0840 G00 Z337.076
N0850 X.004 Y260.408 Z337.525 A-43.937 C89.45
N0860 X.003 Y253.124 Z337.845 A-42.88 C89.901
N0870 Z330.649
N0880 G01 X0.0 Y254.124 Z327.649 F300.
N0890 Y254.155 Z327.648 A-42.885 F500.
N0900 X.001 Y254.446 Z327.637 A-42.93
N0910 X0.0 Y255.01 Z327.614 A-43.018 C89.902
N0920 X.001 Y256.146 Z327.566 A-43.195
N0930 X0.0 Y260.689 Z327.338 A-43.903 C89.905
N0940 Y265.23 Z327.054 A-44.611 C89.907
N0950 Y267.507 Z326.89 A-44.966 C89.908
N0960 Y267.648 Z326.88 A-44.988
N0970 Z329.88 F800.
N0980 G00 Z337.08
N0990 X-.008 Y258.965 Z337.604 A-43.712 C90.381
N1000 X-.021 Y250.286 Z337.944 A-42.438 C90.876
N1010 Z330.747
N1020 G01 X0.0 Y251.286 Z327.747 F300.
N1030 X-.001 Y251.356 Z327.745 A-42.449 F500.
N1040 X0.0 Y251.638 Z327.736 A-42.493 C90.874
N1050 Y260.729 Z327.336 A-43.909 C90.832
N1060 Y267.679 Z326.877 A-44.993 C90.801
N1070 Z329.877 F800.
N1080 G00 Z337.077
N1090 X-.019 Y257.168 Z337.695 A-43.432 C91.33
N1100 X-.045 Y246.656 Z338.037 A-41.873 C91.89
N1110 Y246.657 Z330.841
N1120 G01 X0.0 Y247.656 Z327.841 F300.
N1130 Y247.797 Z327.838 A-41.895 C91.888 F500.
N1140 X.001 Y248.37 Z327.825 A-41.984 C91.882
N1150 X0.0 Y249.507 Z327.798 A-42.161 C91.871
N1160 Y251.773 Z327.732 A-42.514 C91.848
N1170 X.001 Y260.856 Z327.328 A-43.929 C91.758
N1180 X-.001 Y265.398 Z327.042 A-44.637 C91.716
N1190 X.001 Y267.667 Z326.878 A-44.991 C91.694
N1200 (A=-45.01299999999999800)
N1210 X0.0 Y267.808 Z326.868 A-45. C91.693
N1220 (A=-45.01299999999999800)
N1230 Z329.868 F800.
N1240 (A=-45.01299999999999800)
N1250 G00 Z337.068
N1260 X-.03 Y261.442 Z337.464 A-44.098 C92.217
N1270 X-.066 Y255.092 Z337.765 A-43.186 C92.758
N1280 Z330.568
N1290 G01 X0.0 Y256.09 Z327.568 F300.
N1300 Y256.121 Z327.567 A-43.191 C92.757 F500.
N1310 Y256.262 Z327.561 A-43.213 C92.755
N1320 Y256.544 Z327.548 A-43.257 C92.751
N1330 Y261.082 Z327.316 A-43.964 C92.684
N1340 (A=-45.00199999999999500)
N1350 Y267.737 Z326.873 A-45. C92.588
N1360 (A=-45.00199999999999500)
N1370 Z329.873 F800.
N1380 (A=-45.00199999999999500)
N1390 G00 Y267.738 Z377.073
N1400 M9
N1410 M5
(Operation Machine Time: 0.45 minutes)
(Total Operation Machine Time: 0.45 minutes)
N1420 M30
%
作者: linling8    时间: 2004-5-1 15:55
不错不错,贴个PRT学习学习吧
作者: hchhyl    时间: 2004-5-1 22:22
part
作者: 追风侠    时间: 2004-5-2 07:26
再贴个后处理更好
作者: davysun2000    时间: 2004-5-2 10:47
ding xxxxxxxxxxxxx
作者: daowuming    时间: 2004-5-2 15:32
你是UG加工的吧?很好啊!
作者: ycyddh    时间: 2004-5-3 08:37

  

作者: jisx0404    时间: 2004-5-4 13:22
不错,就是机床很怪奥。
作者: hchhyl    时间: 2004-5-4 19:48
四轴和五轴的偏置比较大,另编程时采用了方位不同的坐标系。
作者: jisx0404    时间: 2004-5-5 09:08
后处理是pb做的吗?
作者: hchhyl    时间: 2004-5-5 17:08
两种我都做了(pb&mdfg)
作者: tyf-1000    时间: 2004-5-5 18:31
这个对刀时加工原点怎么确定?
作者: hchhyl    时间: 2004-5-6 19:44
为了简单,就设在转台中心
作者: wave    时间: 2004-5-6 20:19
hchhyl wrote:
为了简单,就设在转台中心

作者: hchhyl    时间: 2004-5-6 22:43
还有一个原因,如果原点不在转台中心,x、y坐标有较大的偏置时,会产生过切,c或a轴角度变化太大。另外在不同程序连续加工快进时要小心,用vericut模拟好像可以,实际上机床时由于线性轴和旋转轴的速度不一样,会撞刀的,我就碰上了这事了,所以安全高度一定要足够。
作者: flash_star    时间: 2004-5-7 10:36
5轴没碰过,关注一下~
作者: lisanbao2008    时间: 2008-11-30 14:03
随便看看
   不要介意哦
作者: zzm133    时间: 2008-12-1 20:44

谢谢看看
、最好有个后处理
作者: camel_hawk    时间: 2009-2-25 12:47
AAAAAAAAAA
作者: miaomenkou    时间: 2009-8-4 16:17
顶了
作者: 旺仔UG    时间: 2009-10-21 23:24
进来学习了
作者: xdlight    时间: 2010-7-29 22:03
羡慕!羡慕!!
作者: cang986926    时间: 2010-9-17 09:00
楼主  +QQ聊下吧  我对你的五轴痴迷到不要老婆啦
作者: chenjunwen    时间: 2010-10-20 00:53
dddddddddddddddd
作者: wuzhaojun555    时间: 2010-10-21 20:39
我也来学习一下.支持
作者: huangdefu750    时间: 2010-11-4 13:44
good very good
作者: wj173733951    时间: 2010-11-5 20:19
楼主开粗是用了3轴吧!
作者: liuliuliuliuliu    时间: 2011-1-24 10:42
不错,就是机床很怪奥。
作者: zhu111bin    时间: 2011-6-29 23:10
顶瓜瓜..................
作者: wd378324758    时间: 2011-12-20 12:03
下下来研究一下!!
作者: 178188704    时间: 2013-2-19 10:28
进来学习的 很好
作者: feihong94236    时间: 2015-1-27 11:00
楼主  +QQ聊下吧  我对你的五轴痴迷到不要老婆啦
作者: qingwawanz    时间: 2016-6-1 19:22
相互学习,共同进步!~
作者: 墨水の内涵    时间: 2016-8-13 20:58
谢谢你的分享




欢迎光临 iCAx开思网 (https://www.icax.org/) Powered by Discuz! X3.3