iCAx开思网

标题: 请问每次换刀都输出刀具信息详设步数?我设败了 [打印本页]

作者: ssfjyv 时间: 2006-2-11 12:15
标题: 请问每次换刀都输出刀具信息详设步数?我设败了
请问每次换刀都输出如下格式刀具信息详设setup(在POST BUILDER中设置):
(TOOL MILL D10.0 R5.0)
M06 T12
在ADD Block Operator Massage中填Tool Diameter: $mom_tool_diameter处理时报警

[ 本帖最后由 ssfjyv 于 2006-2-11 15:37 编辑 ]

作者: wupengcheng 时间: 2006-2-11 13:14
//===============================================================================================
//                                  T O O L L I S T
//===============================================================================================
//
//-----------------------------------------------------------------------------------------------
//MILL                DESCRIPTION       DIAMETER COR RAD FLUTE LEN  ADJ REG
//-----------------------------------------------------------------------------------------------
//D8                平底刀 8 mm          8.0000    0.0000    8.0000    0
//D6R0.5             牛鼻刀 6R0.5 mm       6.0000    0.5000    30.0000 0
//D2R1                波头刀 2 mm          2.0000    1.0000    5.0000    0
//===============================================================================================
G90G28Z0

M30
//==========================================
// TOTAL Machine Time: 69.10
//------------------------------------------

#
# The desired tool list type can be set by changing the code below.
# The default is set to "GROUP_BY_TYPE".
#

global mom_sys_tool_list_initialized
global mom_sys_tool_list_output_type

if { ![info exists mom_sys_tool_list_initialized] || !$mom_sys_tool_list_initialized } {
   MOM_output_to_listing_device "proc PB_CMD_init_tool_list must be executed in the Start of Program before

PB_CMD_create_tool_list is called."
return
}

  #++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
  # Set mom_sys_tool_list_output_type to the desired output fashion.
  #
  # "ORDER_IN_USE"    - List tools used in the program in the order of operations.
  # "ALL_UNIQUE"    - List all unique tools once for each in the order of use.
  # "GROUP_BY_TYPE" - List tools in groups of different tool types.
  #
  #++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
  # set mom_sys_tool_list_output_type "ORDER_IN_USE"
  # set mom_sys_tool_list_output_type "ALL_UNIQUE"
set mom_sys_tool_list_output_type "GROUP_BY_TYPE"

global mom_sys_control_out mom_sys_control_in
global current_program_name
global mom_tool_number mom_tool_length_adjust_register mom_tool_name

  #----------------------------------------------------------------------------
  # Save info for the currently active tool in the program being post-prcessed
  # before starting Shop Doc mechanism for tool list generation.
  #----------------------------------------------------------------------------
if [llength [info commands PB_CMD_save_active_oper_tool_data] ] {
   PB_CMD_save_active_oper_tool_data
}

  #-----------------------------------------------------------
  # Create tool list per selected top-level group.
  # Group name is set to blank if no group has been selected.
  #-----------------------------------------------------------
global mom_parent_group_name

if [info exists mom_parent_group_name] {
   set current_program_name $mom_parent_group_name
} else {
   set current_program_name ""
}

set ci " "
set co " "

if [info exists mom_sys_control_in] { set ci $mom_sys_control_in }
if [info exists mom_sys_control_out] { set co $mom_sys_control_out }

  #*************************
  # Generate tool list data
  #*************************
set template_file pb_post_tool_list.tpl

global tcl_platform
if [string match "windows" $tcl_platform(platform)] {
   set pb_lib_misc_dir [MOM_ask_env_var UGII_BASE_DIR]\\postbuild\\pblib\\misc\\
} else {
   set pb_lib_misc_dir [MOM_ask_env_var UGII_BASE_DIR]/postbuild/pblib/misc/
}

set cam_post_dir    [MOM_ask_env_var UGII_CAM_POST_DIR]
set cam_shop_doc_dir [MOM_ask_env_var UGII_CAM_SHOP_DOC_DIR]

if { [file exists ${pb_lib_misc_dir}${template_file}] } {

   MOM_do_template_file ${pb_lib_misc_dir}${template_file}

} elseif { [file exists ${cam_post_dir}${template_file}] } {

   MOM_do_template_file ${cam_post_dir}${template_file}

} elseif { [file exists ${cam_shop_doc_dir}${template_file}] } {

   MOM_do_template_file ${cam_shop_doc_dir}${template_file}

} else {

   MOM_output_to_listing_device  "ERROR : Template file pb_post_tool_list.tpl is not found in the following directories:

\n \n       $pb_lib_misc_dir \n       $cam_post_dir \n       $cam_shop_doc_dir \n \n       Tool list cannot be

generated.\n"
return
}

  #------------------
  # Tool list header
  #------------------
shop_doc_output_literal

"$co===============================================================================================$ci"
shop_doc_output_literal "$co                                  T O O L L I S T

$ci"
shop_doc_output_literal

"$co===============================================================================================$ci"


  #------------------
  # Output tool list
  #------------------
global tool_data_buffer
global mom_sys_tool_stack

switch $mom_sys_tool_list_output_type {

   "ORDER_IN_USE" {
      set tool_list $mom_sys_tool_stack(IN_USE)
   }

   "GROUP_BY_TYPE" {
      set tool_list [concat $mom_sys_tool_stack(LATHE)  $mom_sys_tool_stack(DRILL)  $mom_sys_tool_stack(MILL)]
   }

   default {
      set tool_list $mom_sys_tool_stack(ALL)
   }
}

set prev_tool_type ""

foreach tool $tool_list {

   set tool_type $tool_data_buffer($tool,type)

   # Output tool type header if it changes.
   if { ![string match "$tool_type" $prev_tool_type] } {
      if { [info exists tool_data_buffer($tool_type,header)] &&  $tool_data_buffer($tool_type,header) != "" } {
         shop_doc_output_literal "$tool_data_buffer($tool_type,header)"
      }
   }

   if [info exists tool_data_buffer($tool,output)] {
      shop_doc_output_literal "$tool_data_buffer($tool,output)"
   }
   set prev_tool_type $tool_type
}

  #------------------
  # Tool list footer
  #------------------
shop_doc_output_literal

"$co===============================================================================================$ci"

  #-------------------------------------------------------------------------------
  # Restore info for the currently active tool in the program being post-prcessed.
  #-------------------------------------------------------------------------------
if [llength [info commands PB_CMD_restore_active_oper_tool_data] ] {
   PB_CMD_restore_active_oper_tool_data
}

作者: ssfjyv 时间: 2006-2-11 15:50
谢谢PENGCHENG兄!
可否不直接修改TCL文件与DEF文件? 我想在POST BUILDER中设置,怎么做?如要修改TCL文件与DEF文件怎么做?(但这会使它们与PUI文件,POST BUILDER失去联系)

欢迎光临 iCAx开思网 (https://www.icax.org/)