iCAx开思网

标题: UG的点位加工 [打印本页]

作者: huhuhu 时间: 2006-12-15 23:57
标题: UG的点位加工
以前曾经在坛子里见过,点位加工时(即钻孔)无做循环加工指令,只有G00各G01,无G83,不知是否为后处理问题或是UG本身问题,还望高人能指点一二,MC里有G83指令的,

作者: 钳子 时间: 2006-12-16 00:10
呵呵

作者: mohonl 时间: 2006-12-16 10:15
很想知道

作者: mohonl 时间: 2006-12-16 10:16
请高手指点怎么才会 "无做循环加工指令,只有G00各G01"

作者: 浮山 时间: 2006-12-19 22:26
据我理解，G83等循环指令，是在给手工编程书写带来简单！道具轨迹实质是差不多的！

作者: 浮山 时间: 2006-12-19 23:22
刚刚我做的有G83的！用的是NX3.0 后置选的三轴如下：
%
N0010 G40 G17 G90 G70
N0020 G91 G28 Z0.0
:0030 T00 M06
N0040 G0 G90 X0.0 Y180. S0 M03
N0050 G43 Z-18. H00
N0060 G83 X0.0 Y180. Z-53.5065 R-17. F250. Q0.0
N0070 G83 X0.0 Y180. Z-50. R-47. Q0.0
N0080 G83 X0.0 Y150. Z-53.5065 R-17. Q0.0
N0090 G83 X0.0 Y150. Z-50. R-47. Q0.0
N0100 G83 X0.0 Y120. Z-53.5065 R-17. Q0.0
N0110 G83 X0.0 Y120. Z-50. R-47. Q0.0
N0120 G83 X0.0 Y90. Z-53.5065 R-17. Q0.0
N0130 G83 X0.0 Y90. Z-50. R-47. Q0.0
N0140 G83 X0.0 Y60. Z-53.5065 R-17. Q0.0
N0150 G83 X0.0 Y60. Z-50. R-47. Q0.0
N0160 G83 X0.0 Y30. Z-53.5065 R-17. Q0.0
N0170 G83 X0.0 Y30. Z-50. R-47. Q0.0
N0180 G83 X0.0 Y0.0 Z-53.5065 R-17. Q0.0
N0190 G83 X0.0 Y0.0 Z-50. R-47. Q0.0
N0200 G83 X30. Y0.0 Z-53.5065 R-17. Q0.0
N0210 G83 X30. Y0.0 Z-50. R-47. Q0.0
N0220 G83 X30. Y30. Z-53.5065 R-17. Q0.0
N0230 G83 X30. Y30. Z-50. R-47. Q0.0
N0240 G83 X30. Y60. Z-53.5065 R-17. Q0.0
N0250 G83 X30. Y60. Z-50. R-47. Q0.0
N0260 G83 X30. Y90. Z-53.5065 R-17. Q0.0
N0270 G83 X30. Y90. Z-50. R-47. Q0.0
N0280 G83 X30. Y120. Z-53.5065 R-17. Q0.0
N0290 G83 X30. Y120. Z-50. R-47. Q0.0
N0300 G83 X30. Y150. Z-53.5065 R-17. Q0.0
N0310 G83 X30. Y150. Z-50. R-47. Q0.0
N0320 G83 X30. Y180. Z-53.5065 R-17. Q0.0
N0330 G83 X30. Y180. Z-50. R-47. Q0.0
N0340 G83 X60. Y0.0 Z-53.5065 R-17. Q0.0
N0350 G83 X60. Y0.0 Z-50. R-47. Q0.0
N0360 G83 X60. Y30. Z-53.5065 R-17. Q0.0
N0370 G83 X60. Y30. Z-50. R-47. Q0.0
N0380 G83 X60. Y60. Z-53.5065 R-17. Q0.0
N0390 G83 X60. Y60. Z-50. R-47. Q0.0
N0400 G83 X60. Y90. Z-53.5065 R-17. Q0.0
N0410 G83 X60. Y90. Z-50. R-47. Q0.0
N0420 G83 X60. Y120. Z-53.5065 R-17. Q0.0
N0430 G83 X60. Y120. Z-50. R-47. Q0.0
N0440 G83 X60. Y150. Z-53.5065 R-17. Q0.0
N0450 G83 X60. Y150. Z-50. R-47. Q0.0
N0460 G83 X90. Y150. Z-53.5065 R-17. Q0.0
N0470 G83 X90. Y150. Z-50. R-47. Q0.0
N0480 G83 X90. Y120. Z-53.5065 R-17. Q0.0
N0490 G83 X90. Y120. Z-50. R-47. Q0.0
N0500 G83 X90. Y90. Z-53.5065 R-17. Q0.0
N0510 G83 X90. Y90. Z-50. R-47. Q0.0
N0520 G83 X90. Y60. Z-53.5065 R-17. Q0.0
N0530 G83 X90. Y60. Z-50. R-47. Q0.0
N0540 G83 X90. Y30. Z-53.5065 R-17. Q0.0
N0550 G83 X90. Y30. Z-50. R-47. Q0.0
N0560 G83 X90. Y0.0 Z-53.5065 R-17. Q0.0
N0570 G83 X90. Y0.0 Z-50. R-47. Q0.0
N0580 G80
N0590 G0 Z-18.
N0600 M02
%

作者: jinc1984 时间: 2007-1-8 21:03
你们的程序等着撞吧

作者: huhuhu 时间: 2007-2-6 21:51
终于弄好了,跟MC一样

作者: 931167965 时间: 2012-10-9 14:51
这个也不行

欢迎光临 iCAx开思网 (https://www.icax.org/)