iCAx开思网

标题: MPost中怎样把A(旋转轴)的值放到X值和Y值前面啊 [打印本页]

作者: lxykkk 时间: 2007-1-16 11:08
标题: MPost中怎样把A(旋转轴)的值放到X值和Y值前面啊
MPost中怎样把A(旋转轴)的值放到X值和Y值前面啊，我改了配置文件中的次序可没用，恳请各位指点。

作者: sinderal 时间: 2007-1-18 12:19
把你用的xxxxx.M4 貼上來, 偶幫你看看

作者: lxykkk 时间: 2007-1-19 08:22
谢版大，如下：

name HAAS 4 axis (Metric)

% 00
/ 00
O >4
N >4
G >2
g >2 G
X ->4.>3
Y ->4.>3
Z ->4.>3
A ->4.>3 W Limit -8000 8000
I ->4.>3
J ->4.>3
K ->4.>3
Q ->4.>3
R ->4.>3
P >40
F >3.1
H >2
D >2
T >2
M >2
S >4

ModalLetters X Y Z F A

ModalGs 0 1 2 3 73 74 76 80 81 82 83 84 85

Sequence#s N 0 1 1
First#? N
Last#? N

HCode X
VCode Y
Dcode Z
FeedCode F

Comment ( )

Spindle 3 4 5
Coolant 8 9 7
DComp 41 42 40
LComp 43 49

Feed G<1>
Rapid G<0>
Cw G<2>
Ccw G<3>

Inc/Abs G 91 90

CtrCode I J
Helical? Y

Spaces? Y

Incremental? N
CtrIncremental? Y
ByQuadrants? N

UppercaseComments? Y

Drill                               # Drilling canned/manual cycle
G81 X[H] Y[V] Z[D] R[Vclear] F[FRate]
end cancel

Peck                               # Pecking canned/manual cycle
G83 X[H] Y[V] Z[D] Q[VBite] R[Vclear] F[FRate]
end cancel

Tap                                  # Tapping canned/manual cycle
G84 X[H] Y[V] Z[D] R[Vclear] F[Frate] Q[VBite]
end cancel

LTap                               # Left handed tapping cycle
G74 X[H] Y[V] Z[D] R[Vclear] F[FRate]
end cancel

Ream                               # Reaming canned/manual cycle
G85 X[H] Y[V] Z[D] R[Vclear] F[FRate]
end cancel

Bore                               # Boring canned/manual cycle
G86 X[H] Y[V] Z[D] R[Vclear] F[FRate]
end cancel

Back                               # Back boring canned/manual cycle
G87 X[H] Y[V] Z[D] R[Vclear] F[FRate]
end cancel

Cancel                               # Cancel a canned/manual cycle
G80
end

Index X                            # Index the rotary table
G0 G49 G90 Z0
G[Work] X[H] Y[V] A[Rotangle]
G43 Z[D] H[Lcomp] M[Cool]
End

UnWind                               # Unwind the rotary table
G0 G49 G90 Z0
A0
G43 Z[D] H[Lcomp] M[Cool]
G0 X[LastH] Y[LastV] A[LastRotAng]
G1 Z[LastD]
End

StartCode                            # Start of the program
%0
O[Program#]
G90 G80 G40 G17
End

1stToolChange                      # First tool change
T[Tool] M6
M[Direct] S[Speed]
G0 G[Work] X[H] Y[V] A[Rotangle]
G43 Z[D] H[Lcomp]
M[Cool]
End

Infeed                               # Enable cutter comp
G[Side] X[H] Y[V] D[DComp] A[Rotangle] F[FRate]
end

Outfeed                            # Disable cutter comp
G1 G40 X[H] Y[V]
Z[D]
end

ToolChange                         # Secondary tool changes
G0 G49 Z0 M9
N[Block] T[Tool] M6
G0 G90 G[Work] X[H] Y[V] S[Speed] M[Direct] A[Rotangle]
G43 Z[D] H[Lcomp] M[Cool]
End

EndCode                            # End of the program
G0 G49 G90 Z0 M9
G28 g91 Y0 Z0 A0
M30
%0
End

我想用HASS的改一下，我把边部分的输出次序改过但无作用。

作者: sinderal 时间: 2007-1-21 10:40
name HAAS 4 axis (Metric)

% 00
/ 00
O >4
N >4
G >2
g >2 G
A ->4.>3 W Limit -8000 8000 <----------- 移到 X Y Z 前面
X ->4.>3
Y ->4.>3
Z ->4.>3
I ->4.>3
J ->4.>3
K ->4.>3
Q ->4.>3
R ->4.>3
P >40
F >3.1
H >2
D >2
T >2
M >2
S >4

......
......

作者: lxykkk 时间: 2007-1-24 20:07
谢谢版大,已搞定.

欢迎光临 iCAx开思网 (https://www.icax.org/)