iCAx开思网

标题: 请教结果 [打印本页]

作者: liangyue 时间: 2007-4-5 16:29
标题: 请教结果
本人进行Cool + Flow.分析
Injection + packing + cooling time Automatic
Injection time Automatic
Velocity/pressure switch-over by % volume       =    99.0000 %
Pack/Holding Control %Filling pressure vs time
Pack/Hold Profile    0 80%
10 80%
结果如下:
Cavity surface temperature - maximum                = 194.2070 C
Cavity surface temperature - minimum                =  33.7150 C
Cavity surface temperature - average                =  43.1120 C
Average mold exterior temperature                   =  26.1130 C
Cycle time calculated from percentage frozen on average part thickness
Cycle time                                        =  10.5505 s

Process parameters :
------------------
Fill time                                        =    1.7850 s
Injection time has been determined by automatic calculation.
Stroke volume determination                      = Automatic
Cycle time                                        =    10.5505 s

Velocity/pressure switch-over by % volume       =    99.0000 %
Packing/holding time                            =    10.0000 s
Pack/hold pressure profile (rel):
      duration  % filling pressure
   ---------------------------------
         0.0000 s          80.0000
         10.0000 s          80.0000
Ambient temperature                               =    25.0000 C
Melt temperature                                  = 235.0000 C
Ideal cavity-side mold temperature                =    60.0000 C
Ideal core-side mold temperature                =    60.0000 C

NOTE: Using mold wall temperature data from cooling analysis

Packing phase:
|-------------------------------------------------------------|
|  Time  |Packing|  Pressure | Clamp force|    Status    |
|  (s) |  (%)  | (MPa) |  (tonne) |                |
|-------------------------------------------------------------|
| 2.16 |  0.00 |    73.07 |    13.84 |       P       |
| 2.50 | 10.07 |    73.07 |    17.51 |       P       |
| 3.00 | 24.81 |    73.07 |    16.29 |       P       |
| 3.50 | 39.55 |    73.07 |    13.91 |       P       |
| 4.00 | 54.29 |    73.07 |    11.28 |       P       |
| 4.50 | 69.03 |    73.07 |    9.43 |       P       |
| 5.00 | 83.77 |    73.07 |    8.15 |       P       |
| 5.50 | 98.51 |    73.07 |    7.09 |       P       |
| 6.00 |100.00 |    73.07 |    6.34 |       P       |
| 6.50 |100.00 |    73.07 |    5.79 |       P       |
| 7.00 |100.00 |    73.07 |    5.36 |       P       |
| 7.50 |100.00 |    73.07 |    5.03 |       P       |
| 8.00 |100.00 |    73.07 |    4.75 |       P       |
| 8.25 |100.00 |    73.07 |    4.64 |       P       |
| 8.50 |100.00 |    73.07 |    4.53 |       P       |
| 8.75 |100.00 |    73.07 |    4.42 |       P       |
| 9.00 |100.00 |    73.07 |    4.33 |       P       |
| 9.25 |100.00 |    73.07 |    4.24 |       P       |
| 9.50 |100.00 |    73.07 |    4.15 |       P       |
| 9.75 |100.00 |    73.07 |    4.07 |       P       |
|  10.00 |100.00 |    73.07 |    3.99 |       P       |
| 1.91 | 96.21 |    91.33 |    14.03 | 7.99 |  V/P  |
|  11.00 |100.00 |    73.07 |    3.72 |       P

是不是成型周期为Cycle time =    10.5505 s,那冷却时间又该是多少
保压是否到6S就够| 6.50 |100.00 |    73.07 |    5.79 |       P       |
| 1.91 | 96.21 |    91.33 |    14.03 | 7.99 |  V/P  |是什么意识

[ 本帖最后由 liangyue 于 2007-4-5 16:31 编辑 ]

欢迎光临 iCAx开思网 (https://www.icax.org/)