iCAx开思网

标题: 此段刀补程序机床执行不了? [打印本页]

作者: yuequer 时间: 2008-1-26 10:47
标题: 此段刀补程序机床执行不了?
程序如下:
G40 G17 G49 G80 G90 M09 G54
G00 G90 X-52.076 Y52.076 S3200 M03
G43 Z20. H00
Z-0.2
G41 G01 X-54.905 Y54.905 F1000. D01
G03 X-59.454 Y27.083 I17.075 J-17.075 F2500.
G02 Y-27.083 I-54.494 J-27.083
G03 X-27.083 Y-59.454 I21.624 J-10.747
G02 X27.083 I27.083 J-54.494
G03 X59.454 Y-27.083 I10.747 J21.624
G02 Y27.083 I54.494 J27.083
G03 X27.083 Y59.454 I-21.624 J10.747
G02 X-27.083 I-27.083 J54.494
G03 X-54.905 Y54.905 I-10.747 J-21.624
G40
G00 X-53.49 Y53.49
X-52.069 Y52.069 Z-0.4
G41 G01 X-54.897 Y54.897 F1000. D01
G03 X-59.444 Y27.088 I17.067 J-17.067 F2500.
G02 Y-27.088 I-54.504 J-27.088
G03 X-27.088 Y-59.444 I21.614 J-10.742
G02 X27.088 I27.088 J-54.504
G03 X59.444 Y-27.088 I10.742 J21.614
G02 Y27.088 I54.504 J27.088
G03 X27.088 Y59.444 I-21.614 J10.742
G02 X-27.088 I-27.088 J54.504
G03 X-54.897 Y54.897 I-10.742 J-21.614
G40Sample Text

机床运行状况是:
将刀补值改为"0"就可执行;
一加数值就出错!

是什么缘故?

[ 本帖最后由 yuequer 于 2008-1-26 10:48 编辑 ]

作者: GGGNNN 时间: 2008-1-27 14:40
X-52.076 Y52.076
X-54.905 Y54.905
此两点距离得大于刀补值
另G40在移动的程序段
G40 G00 X-53.49 Y53.49

作者: yuequer 时间: 2008-2-2 09:52
脨禄脨禄,脟毛脦脢脗楼脡脧碌脛,脭玫脙麓脩霉脨脼赂脛潞贸麓娄脌铆虏脜脛脺脢鹿G40 G00/G01 脭脷脥卢脪禄脨脨脛脴?

作者: open_lian 时间: 2008-2-2 15:51
脜录脪虏虏禄禄谩..

作者: lisanbao2008 时间: 2008-11-18 15:33
你走的距离要大于你的刀具半径

欢迎光临 iCAx开思网 (https://www.icax.org/)