iCAx开思网

标题: 米克朗后处理文件，什么条件我都答应 [打印本页]

作者: 平淡的喜悦 时间: 2008-8-3 18:51
标题: 米克朗后处理文件，什么条件我都答应
N4。N5都可以，13942057720 兄弟们都能理解我现在的心情/ 真的是太急了没有办法，所以来这个最大的论坛，我相信有高手，我期待。。。。。。

程序头：
10 BEGIN PGM  M11EA MM
11 CYCL DEF 7.0 DATUM SHIFT
12 CYCL DEF 7.1 IX+0
13 CYCL DEF 7.2 IY+0
14 CYCL DEF 7.3 IZ-0.03
15 ; Date : 12.06.2007 - 15:32:36
16 ; TL TYPE : ENDMILL
17 ; TL ID : D10R0T1
18 ; TL DIA. 10.  LENGTH 20.
19 TOOL CALL 1 Z S8000
  Q7= 200       ; PLUNGE FEEDRATE
  Q8= 2000    ; CUTTING FEEDRATE
20 M03
21 CALL PGM TNC:\EWHA\MEAS\MEAS.H
22 CYCL DEF 32.0 TOLERANCE
23 CYCL DEF 32.1 T0.01
24 TOOL CALL 1 Z
25 M07
26 CYCL DEF 9.0 DWELL TIME
27 CYCL DEF 9.1 DWELL 5
28 ;
29 ; TL PATH : 01-1
30 ;
31 L X+0.0 Y+0.0 F8000 M03
32 L Z+10.000 F8000
33 L Y+14.653 F8000
34 L Z+1.050 F8000
35 L Z+0.010 FQ7
36 L Y+14.403 FQ8
37 CC X-3.536 Y+14.403
38 C X-1.036 Y+11.903 DR-
39 CC X+0.0 Y+10.867
40 C X+0.0 Y+9.403 DR+
41 CC X+0.0 Y+0.0
42 C X+9.403 Y+0.0 DR-
43 CC X+0.0 Y+0.0
44 C X-9.403 Y+0.0 DR-
45 CC X+0.0 Y+0.0
46 C X+0.0 Y+9.403 DR-
47 CC X+0.0 Y+11.853
48 C X+0.0 Y+14.303 DR+
49 CC X+0.0 Y+9.353
50 C X+0.0 Y+4.403 DR+
51 CC X+0.0 Y+0.0
52 C X+4.403 Y+0.0 DR-
53 CC X+0.0 Y+0.0
54 C X-4.403 Y+0.0 DR-
55 CC X+0.0 Y+0.0
56 C X+0.0 Y+4.403 DR-
57 CC X+0.0 Y+9.403
58 C X+0.0 Y+14.403 DR+
59 L X+6.926 Y+12.913 Z-0.010
60 L X+6.808 Y+12.692
61 CC X+3.692 Y+14.363
62 C X+4.714 Y+10.979 DR-
63 CC X+5.137 Y+9.577
64 C X+4.444 Y+8.286 DR+
65 CC X+0.0 Y+0.0
66 C X+9.403 Y+0.0 DR-
67 CC X+0.0 Y+0.0
68 C X+7.833 Y-5.201 DR-
69 L X+7.845 Y-5.064
70 L X+7.854 Y-4.927
71 L X+7.875 Y-4.480
72 L X+7.880 Y-4.255
73 L X+7.875 Y-4.031
74 L X+7.856 Y-3.584
75 L X+7.841 Y-3.359
76 L X+7.816 Y-3.135
77 L X+7.756 Y-2.688
78 L X+7.721 Y-2.462
79 L X+7.675 Y-2.238
80 L X+7.573 Y-1.791
81 L X+7.515 Y-1.565
82 L X+7.448 Y-1.341
83 L X+7.300 Y-0.895
84 L X+7.241 Y-0.725
85 L X+7.176 Y-0.558
86 L X+7.083 Y-0.332
87 L X+7.035 Y-0.219
88 L X+6.984 Y-0.107
89 L X+6.881 Y+0.114
90 L X+6.797 Y+0.284
91 L X+6.706 Y+0.451
92 L X+6.453 Y+0.898
93 L X+6.367 Y+1.045
94 L X+6.276 Y+1.188
95 L X+6.186 Y+1.325
96 L X+6.108 Y+1.440
97 L X+6.027 Y+1.552
98 L X+5.797 Y+1.862
99 L X+5.687 Y+2.005
100 L X+5.572 Y+2.143
101 L X+5.355 Y+2.396
102 L X+5.257 Y+2.506
103 L X+5.156 Y+2.613
104 L X+4.967 Y+2.808
105 L X+4.939 Y+2.837
106 L X+4.911 Y+2.865
107 L X+2.865 Y+4.911
108 L X+2.837 Y+4.939
109 L X+2.808 Y+4.967

[ 本帖最后由平淡的喜悦于 2008-8-3 18:54 编辑 ]

作者: 54benq 时间: 2008-8-3 21:51
不懂帮不上忙

作者: o0傑嘫吥鮦0o 时间: 2008-8-3 23:22
% 833H10J G71 G50
;Tungkong Mikron Post V19.0 By HHS in 2002
;Time: Sun Aug 03 23:18:26 2008
;Cutter Name: D10R0.5
N2 G40 S15000 M03
N3 G00 G90 X-38.7809 Y-3.2509
N4 Z15.0000
N5 Z-4.3012
N6 Z-4.3811
N7 G01 Z-5.3811 F10000
N8 G03 X-35.6214 Y-.9704 I-38.5363 J-.2609
N9 G02 X-34.8464 Y.7901 I-30.2811 J-2.2703 F10000
N10 X-33.4224 Y2.2334 I-30.3192 J-2.2525
N11 X-30.3789 Y3.1841 I-30.3666 J-2.2024
N12 G01 X19.2102 Y3.1827
N13 G02 X22.2711 Y2.2334 I19.1374 J-2.4614
N14 X23.2310 Y1.4247 I18.9398 J-2.6945
N15 X25.9115 Y-1.3129 I-132.1587 J-153.4073
N16 X27.3509 Y-4.9136 I21.6924 J-5.0876
N17 G01 X27.3573 Y-5.3603
N18 X27.3570 Y-8.9338
N19 G02 X25.9115 Y-12.5388 I21.9838 J-8.8716
N20 G01 X25.4800 Y-12.9540
N21 G02 X24.8811 Y-13.4007 I20.7681 J-7.2613
N22 X21.8907 Y-14.2736 I21.9048 J-8.7633
N23 G01 X-30.8257 Y-14.2739

作者: 黄瓜 时间: 2008-8-4 02:28
什么类型的机床？
ＵＣＰ？ＨＳＭ　ＸＸ　Ｕ？
不觉得有什么特别的　

作者: liang617420 时间: 2008-8-4 17:32
什么类型的机床？

作者: 平淡的喜悦 时间: 2008-8-5 12:11
是没有什么但是没有后处理文件,

作者: ZYL_LK_2008 时间: 2008-8-15 10:24
看不动啊

作者: EMKEX 时间: 2008-8-15 17:33
hsm400的后处理

欢迎光临 iCAx开思网 (https://www.icax.org/)