iCAx开思网

标题: adams -- ansys，载荷文件的导入 [打印本页]

作者: 20070011 时间: 2009-4-11 11:46
标题: adams -- ansys，载荷文件的导入
想请教大家一个关于adans载荷文件导入ansys后出现的问题
我是
1）将ansys生成的MNF文件导入ADAMS
2）修改旋转副，用导入的弹性体替换原来刚体
3)仿真分析，载荷文件导出，设置时间为0.5S,最后载荷文件的输出时输出的是连接点的载荷，而不是所有节点载荷（不知道这是不是出错了）
各个连接点载荷是F, 6, FX,1.66570e+001
F, 6, FY,-3.33852e+001
F, 6, FZ,1.93665e+000
F, 6, MX,4.40979e-001
F, 6, MY,-7.95834e+000
F, 6, MZ,9.65723e-007
F, 1, FX,-2.62559e+003
F, 1, FY,1.33464e+003
F, 1, FZ,-4.42698e+000
F, 1, MX,2.80243e-001
F, 1, MY,3.80271e+000
F, 1, MZ,-4.38924e-007
F, 2, FX,-2.60549e+003
F, 2, FY,1.32483e+003
F, 2, FZ,-4.77824e+000
F, 2, MX,5.57923e-001
F, 2, MY,4.02435e+000
F, 2, MZ,-4.64507e-007
F, 3, FX,2.15113e+001
F, 3, FY,-1.47548e+001
F, 3, FZ,1.23283e+001
F, 3, MX,-2.90089e-001
F, 3, MY,1.26137e+001
F, 3, MZ,4.26824e-006
F, 4, FX,2.15112e+001
F, 4, FY,-1.47549e+001
F, 4, FZ,-2.76300e+000
F, 4, MX,-2.54301e+000
F, 4, MY,2.77410e+000
F, 4, MZ,-3.07488e-007
F, 8, FX,1.62589e+003
F, 8, FY,-3.84870e+002
F, 8, FZ,4.23771e+001
F, 8, MX,-1.46706e+000
F, 8, MY,-5.91596e+000
F, 8, MZ,-4.96373e-005
F, 7, FX,1.64206e+003
F, 7, FY,-3.88920e+002
F, 7, FZ,-5.19402e+001
F, 7, MX,-4.81260e-001
F, 7, MY,8.71656e+000
F, 7, MZ,2.67433e-004
F, 5, FX,1.66571e+001
F, 5, FY,-3.33852e+001
F, 5, FZ,7.26573e+000
F, 5, MX,-9.95902e-001
F, 5, MY,-7.32185e+000
F, 5, MZ,2.81382e-007
4）然后就是启动ansys导入载荷文件，我直接将上面的文件导入，不知道是不是正确，因为从网上看到的说明说应该是对应时间的载荷
5)ansys---solution---solve--current LS--分析
6）读取节点载荷first set
7）list resoult 发现所有节点应力都为0！！
请大家帮帮忙

欢迎光临 iCAx开思网 (https://www.icax.org/)