iCAx开思网

标题: proe5.0同时挂emx4.1和emx5.0，已经验证OK [打印本页]

作者: zstdv 时间: 2009-5-15 10:02
标题: proe5.0同时挂emx4.1和emx5.0，已经验证OK
昨晚，根据网上介绍自己组合proe5.0同时挂emx4.1和emx5.0，验证OK，并非原创。

作者: zstdv 时间: 2009-5-15 10:04
1、Pro ENGINEER 5.0挂EMX4.1
1），确保，  盘符：\EMX4.1安装路径\i486_nt下有emx41_wf.dll文件
2），修改，盘符：\EMX4.1安装路径\text下的protk.dat文件如下：
name EMX 4.1 M180
startup dll
exec_file  盘符：\EMX4.1安装路径/$PRO_MACHINE_TYPE/emx41_wf.dll
text_dir 盘符：\EMX4.1安装路径\EMX 4.1
revision 23.0
allow_stop true
unicode_encoding false
end
完成后保存。
2、Pro ENGINEER 5.0挂EMX5.0
1），确保，  盘符：\EMX5.0安装路径\i486_nt下有emx50_wf4.dll，shc50_wf4.dll两个文件
2），修改，盘符：\EMX4.1安装路径\text下的protk.dat文件如下：
name EMX 5.0 M050
startup dll
exec_file 盘符：\EMX5.0安装路径\i486_nt\emx50_wf4.dll
text_dir  盘符：\EMX5.0安装路径\text
revision 24.0
allow_stop true
unicode_encoding false
end
完成后保存

3、在你的Pro ENGINEER 5.0的configro中加入以下内容，打开Pro ENGINEER 5.0就可以使用EMX4.1和EMX5.0.
mapkey buwprojna @MAPKEY_NAMEDefine new project;\
mapkey(continued) @MAPKEY_LABELDefine new project;~ Activate `main_dlg_cur` `CreateProject`;
mapkey buwprodatanzaend @MAPKEY_NAMEModify project;\
mapkey(continued) @MAPKEY_LABELModify project;~ Activate `main_dlg_cur` `EditProject`;
mapkey buwproaufb @MAPKEY_NAMEPrepare project;@MAPKEY_LABELPrepare project;\
mapkey(continued) ~ Activate `main_dlg_cur` `PrepareProject`;
mapkey buwwezedef @MAPKEY_NAMEDefine Moldbase Assembly;\
mapkey(continued) @MAPKEY_LABELDefine Moldbase Assembly;\
mapkey(continued) ~ Activate `main_dlg_cur` `MoldbaseDefinition`;
mapkey buwcomp @MAPKEY_NAMEAssemble/Disassemble Components;\
mapkey(continued) @MAPKEY_LABELAssemble/Disassemble Components;\
mapkey(continued) ~ Activate `main_dlg_cur` `ComponentStatus`;
mapkey buwcrequ @MAPKEY_NAMEDefine equipment on existing point;\
mapkey(continued) @MAPKEY_LABELDefine equipment on existing point;\
mapkey(continued) ~ Activate `main_dlg_cur` `DefineEquipment`;
mapkey buwmodequi @MAPKEY_NAMERedefine equipment;\
mapkey(continued) @MAPKEY_LABELRedefine equipment;\
mapkey(continued) ~ Activate `main_dlg_cur` `RedefineEquipment`;
mapkey buwdelequi @MAPKEY_NAMEDelete equipment;@MAPKEY_LABELDelete equipment;\
mapkey(continued) ~ Activate `main_dlg_cur` `DeleteEquipment`;
mapkey buwcreguide @MAPKEY_NAMEDefine guide on existing point;\
mapkey(continued) @MAPKEY_LABELDefine guide on existing point;\
mapkey(continued) ~ Activate `main_dlg_cur` `DefineGuide`;
mapkey buwmodguide @MAPKEY_NAMERedefine guide;@MAPKEY_LABELRedefine guide;\
mapkey(continued) ~ Activate `main_dlg_cur` `RedefineGuide`;
mapkey buwdelguide @MAPKEY_NAMEDelete guide;@MAPKEY_LABELDelete guide;\
mapkey(continued) ~ Activate `main_dlg_cur` `DeleteGuide`;
mapkey buwspavpk @MAPKEY_NAMEDefine screw on existing point;\
mapkey(continued) @MAPKEY_LABELDefine screw on existing point;\
mapkey(continued) ~ Activate `main_dlg_cur` `DefineScrewExisting`;
mapkey buwcrscrmse @MAPKEY_NAMEDefine screw on mousepoint;\
mapkey(continued) @MAPKEY_LABELDefine screw on mousepoint;\
mapkey(continued) ~ Activate `main_dlg_cur` `DefineScrewMouse`;
mapkey buwscrred @MAPKEY_NAMERedefine screw;@MAPKEY_LABELRedefine screw;\
mapkey(continued) ~ Activate `main_dlg_cur` `RedefineScrew`;
mapkey buwschrdel @MAPKEY_NAMEDelete screw;@MAPKEY_LABELDelete screw;\
mapkey(continued) ~ Activate `main_dlg_cur` `DeleteScrew`;
mapkey buwsavp @MAPKEY_NAMEDefine dowel pin on existing point;\
mapkey(continued) @MAPKEY_LABELDefine dowel pin on existing point;\
mapkey(continued) ~ Activate `main_dlg_cur` `DefinePinExisting`;
mapkey buwstmouse @MAPKEY_NAMEDefine dowel pin on mousepoint;\
mapkey(continued) @MAPKEY_LABELDefine dowel pin on mousepoint;\
mapkey(continued) ~ Activate `main_dlg_cur` `DefinePinMouse`;
mapkey buwstred @MAPKEY_NAMERedefine Dowel pin;\
mapkey(continued) @MAPKEY_LABELRedefine Dowel pin;~ Activate `main_dlg_cur` `RedefinePin`;
mapkey buwstdel @MAPKEY_NAMEDelete dowel pin;@MAPKEY_LABELDelete dowel pin;\
mapkey(continued) ~ Activate `main_dlg_cur` `DeletePin`;
mapkey buwapavp @MAPKEY_NAMEDefine ejector pin on existing point;\
mapkey(continued) @MAPKEY_LABELDefine ejector pin on existing point;\
mapkey(continued) ~ Activate `main_dlg_cur` `DefineEjectorExisting`;
mapkey buwapampp @MAPKEY_NAMEDefine ejector pin on mousepoint;\
mapkey(continued) @MAPKEY_LABELDefine ejector pin on mousepoint;\
mapkey(continued) ~ Activate `main_dlg_cur` `DefineEjectorMouse`;
mapkey buwausred @MAPKEY_NAMERedefine Ejector pin;\
mapkey(continued) @MAPKEY_LABELRedefine Ejector pin;\
mapkey(continued) ~ Activate `main_dlg_cur` `RedefineEjector`;
mapkey buwausdel @MAPKEY_NAMEDelete ejector pin;\
mapkey(continued) @MAPKEY_LABELDelete ejector pin;~ Activate `main_dlg_cur` `DeleteEjector`;
mapkey buwkueerz @MAPKEY_NAMECreate cooling bore;\
mapkey(continued) @MAPKEY_LABELCreate cooling bore;~ Activate `main_dlg_cur` `DefineCooling`;
mapkey buwkuered @MAPKEY_NAMERedefine cooling bore;\
mapkey(continued) @MAPKEY_LABELRedefine cooling bore;\
mapkey(continued) ~ Activate `main_dlg_cur` `RedefineCooling`;
mapkey buwkuetankerz @MAPKEY_NAMECreate CoolingTank;\
mapkey(continued) @MAPKEY_LABELRedefine cooling bore;\
mapkey(continued) ~ Activate `main_dlg_cur` `DefineCoolingTank`;
mapkey buwkuedel @MAPKEY_NAMEDelete cooling bore;\
mapkey(continued) @MAPKEY_LABELDelete cooling bore;~ Activate `main_dlg_cur` `DeleteCooling`;
mapkey buwspavp @MAPKEY_NAMEDefine support pillar on existing point;\
mapkey(continued) @MAPKEY_LABELDefine support pillar on existing point;\
mapkey(continued) ~ Activate `main_dlg_cur` `DefineSupportExisting`;
mapkey buwspmouse @MAPKEY_NAMEDefine support pillar on mousepoint;\
mapkey(continued) @MAPKEY_LABELDefine support pillar on mousepoint;\
mapkey(continued) ~ Activate `main_dlg_cur` `DefineSupportMouse`;
mapkey buwsupred @MAPKEY_NAMERedefine support pillar;\
mapkey(continued) @MAPKEY_LABELRedefine support pillar;\
mapkey(continued) ~ Activate `main_dlg_cur` `RedefineSupport`;
mapkey buwsdel @MAPKEY_NAMEDelete support pillar;\
mapkey(continued) @MAPKEY_LABELDelete support pillar;~ Activate `main_dlg_cur` `DeleteSupport`;
mapkey buwvseae @MAPKEY_NAMEChange bom-entry;@MAPKEY_LABELChange bom-entry;\
mapkey(continued) ~ Activate `main_dlg_cur` `EditBOMEntry`;
mapkey buwbomformat @MAPKEY_NAMEFormat Bill of Materials;\
mapkey(continued) @MAPKEY_LABELFormat Bill of Materials;~ Activate `main_dlg_cur` `FormatBOM`;
mapkey buwbomcheck @MAPKEY_NAMECheck BOM-Entries;\
mapkey(continued) @MAPKEY_LABELCheck BOM-Entries;~ Activate `main_dlg_cur` `CheckBOMEntries`;
mapkey buwdeflib @MAPKEY_NAMEPrepare library-component;\
mapkey(continued) @MAPKEY_LABELPrepare library-component;\
mapkey(continued) ~ Activate `main_dlg_cur` `DefineLibraryComp`;
mapkey buwbibasm @MAPKEY_NAMEAssemble library-component;\
mapkey(continued) @MAPKEY_LABELAssemble library-component;\
mapkey(continued) ~ Activate `main_dlg_cur` `AssembleLibraryComp`;
mapkey buwbibredefine @MAPKEY_NAMERedefine library-component;\
mapkey(continued) @MAPKEY_LABELRedefine library-component;\
mapkey(continued) ~ Activate `main_dlg_cur` `RedefineLibraryComp`;
mapkey buw_lib_delete @MAPKEY_NAMEDelete library-component;\
mapkey(continued) @MAPKEY_LABELDelete library-component;\
mapkey(continued) ~ Activate `main_dlg_cur` `DeleteLibraryComp`;
mapkey buwsdae @MAPKEY_NAMEDefine/modify slider;\
mapkey(continued) @MAPKEY_LABELDefine/modify slider;~ Activate `main_dlg_cur` `DefineSlider`;
mapkey buwdelslider @MAPKEY_NAMEDelete Slider;@MAPKEY_LABELDelete Slider;\
mapkey(continued) ~ Activate `main_dlg_cur` `DeleteSlider`;
mapkey buwcreatelifter @MAPKEY_NAMEDefine/Modify Lifter;\
mapkey(continued) @MAPKEY_LABELDefine/Modify Lifter;~ Activate `main_dlg_cur` `DefineLifter`;
mapkey buwdellifter @MAPKEY_NAMEDelete Lifter;@MAPKEY_LABELDelete Lifter;\
mapkey(continued) ~ Activate `main_dlg_cur` `DeleteLifter`;
mapkey buwkliaen @MAPKEY_NAMEDefine latch lock;\
mapkey(continued) @MAPKEY_LABELDefine latch lock;~ Activate `main_dlg_cur` `DefineLatch`;
mapkey buwdellatch @MAPKEY_NAMEDelete latch lock;\
mapkey(continued) @MAPKEY_LABELDelete latch lock;~ Activate `main_dlg_cur` `DeleteLatch`;
mapkey buwwzofg @MAPKEY_NAMEDefine moldbase opening;\
mapkey(continued) @MAPKEY_LABELDefine moldbase opening;\
mapkey(continued) ~ Activate `main_dlg_cur` `DefineSimulation`;
mapkey buwwzani @MAPKEY_NAMESimulate moldbase opening;\
mapkey(continued) @MAPKEY_LABELSimulate moldbase opening;\
mapkey(continued) ~ Activate `main_dlg_cur` `RunSimulation`;
mapkey buwsimstop @MAPKEY_NAMEClose moldbase opening mode;\
mapkey(continued) @MAPKEY_LABELClose moldbase opening mode;\
mapkey(continued) ~ Activate `main_dlg_cur` `QuitSimulation`;
mapkey buwbwdb @MAPKEY_NAMECalculate clamping forces;\
mapkey(continued) @MAPKEY_LABELCalculate clamping forces;\
mapkey(continued) ~ Activate `main_dlg_cur` `CalculateBending`;
mapkey buw_createhc @MAPKEY_NAMECreate Holechart;\
mapkey(continued) @MAPKEY_LABELCreate Holechart;~ Activate `main_dlg_cur` `CreateHolechart`;
mapkey buw_delhc @MAPKEY_NAMEDelete Holech怅rt;@MAPKEY_LABELDelete Holechart;\
mapkey(continued) ~ Activate `main_dlg_cur` `DeleteHolechart`;
mapkey buw_make_hr @MAPKEY_NAMEDefineHotrunner;@MAPKEY_LABELDefineHotrunner;\
mapkey(continued) ~ Activate `main_dlg_cur` `DefineHotrunner`;
mapkey buw_delete_hr @MAPKEY_NAMEDeleteHotrunner;\
mapkey(continued) @MAPKEY_LABELDeleteHotrunner;~ Activate `main_dlg_cur` `DeleteHotrunner`;
mapkey buwtransm_create @MAPKEY_NAMECreate Transmission;\
mapkey(continued) @MAPKEY_LABELCreate Transmission;\
mapkey(continued) ~ Activate `main_dlg_cur` `DefineTransmission`;
mapkey buw_transm_delete @MAPKEY_NAMEDelete Transmission;\
mapkey(continued) @MAPKEY_LABELDelete Transmission;\
mapkey(continued) ~ Activate `main_dlg_cur` `DeleteTransmission`;;
default_ext_ref_scope ALL
set_trail_single_step NO
native_kbd_macros NO
open_simplified_rep_by_default NO
show_dim_sign no
enable_absolute_accuracy yes
accuracy_lower_bound .0000001
protkdat 盘符：\EMX5.0安装路径\text\protk.dat
protkdat 盘符：\EMX4.1安装路径\text\protk.dat

作者: zstdv 时间: 2009-5-15 10:06
emx41_wf.dll，emx50_wf4.dll，shc50_wf4.dll文件网上有很多地方可以下载得到，最主要是在protk.dat文件中添加allow_stop true ；unicode_encoding false 这两句

作者: 高压线 时间: 2009-5-15 10:08
学习了！非常感谢！！！

作者: zstdv 时间: 2009-5-15 10:12
同时试用发现建模和装配环境下出现新的界面，比较新颖，如图片，那个对话框是从左边滑进来的，不过这个使用环境是在建立emx5.0项目后出现的，哪位老大可以修改在启动proe5.0后就出现这个环境

作者: zstdv 时间: 2009-5-15 10:13
版主，没有功劳也有苦劳，给点分不？

作者: 770152630WGM 时间: 2009-5-15 14:22
顶一下
PROE5.0正式版的出来了没有？？

作者: xxd_157 时间: 2009-5-16 08:25
顶顶顶，但我想请问下，在5.0里分模时抽取元件后，大家会发现产品边和分型面会有有条线，这条线很虽说对工程师很好看出产品的分型，但外面做模的就看不懂，请问如何定义配置文件（config.pro）或有其他的好办法，还有，分型面还会着色，期待高手们解决，谢谢了！

作者: MAOYONGMAO1 时间: 2009-5-19 21:47
那是有好处的，因为在正规的图纸中要标明产品区域和碰穿区。

作者: xxd_157 时间: 2009-5-20 11:59
请问能不能不要这条线呢？怎么设置呢？

作者: mikyling 时间: 2009-5-26 21:15
感谢楼主分享！

作者: songwenchong 时间: 2009-6-5 10:40
我用的是proe5.0C000版，昨天我也挂靠了EMX5.0和PDX5.0,而且是在Vista下挂靠的，关键是修改config.win和config.pro时用记事本打开，而且要用管理员方式运行记事本，保存时要务必写扩展名。

作者: funggang 时间: 2009-8-16 15:06
我的Proe 5.0 F000已经挂上EMX4.1，多谢！

作者: wangliye 时间: 2009-9-2 20:36
请问你们的草绘点EMX认可吗？
我的怎么不行啊？
QQ:292476022

作者: xiaoweibin 时间: 2009-9-2 20:45
kanle ..............

作者: colinchi 时间: 2009-9-3 09:19
高手，学习了。有空来交流一下

作者: HTC 时间: 2009-9-12 23:27

xxd_157 发表于 2009-5-16 08:25
顶顶顶，但我想请问下，在5.0里分模时抽取元件后，大家会发现产品边和分型面会有有条线，这条线很虽说对工程师很好看出产品的分型，但外面做模的就看不懂，请问如何定义配置文件（config.pro）或有其他的好办法，还有 ...

4.0就已经有了，我也觉得不好，每次都要把它移除掉才行，有时候碰到一些麻烦点的，还要移除半天，晕4啦........就比如一支镶针是镶在CORE碰穿CAVITY...结果分模出来CAVITY就也的个圆圈...如果不把圆圈移除掉，你打印出来给做模的师傅，人家还以为是一个孔，往那里钻下去不就完了。。。

作者: HTC 时间: 2009-9-12 23:27
9# MAOYONGMAO1
4.0就已经有了，我也觉得不好，每次都要把它移除掉才行，有时候碰到一些麻烦点的，还要移除半天，晕4啦........就比如一支镶针是镶在CORE碰穿CAVITY...结果分模出来CAVITY就也的个圆圈...如果不把圆圈移除掉，你打印出来给做模的师傅，人家还以为是一个孔，往那里钻下去不就完了。。。

作者: HTC 时间: 2009-9-12 23:27

MAOYONGMAO1 发表于 2009-5-19 21:47
那是有好处的，因为在正规的图纸中要标明产品区域和碰穿区。

作者: yiming506 时间: 2009-10-11 12:21
ding,,,,,,,,,,

作者: kand 时间: 2009-10-17 21:18
能得的好贴,建议版主给楼主加分!以示鼓励

作者: Wesleyq 时间: 2009-10-19 15:02
　　　　能有吗？

作者: 鑫源泉 时间: 2009-10-22 23:53
学习学习

作者: 鑫源泉 时间: 2009-10-23 22:29
整了半天也运行不了还望多指教

作者: 我是来玩的 时间: 2009-10-23 22:46
同时挂两个一何用？？

作者: wangyajun 时间: 2009-10-24 13:28
挂上了，很不稳定

作者: 鑫源泉 时间: 2009-10-29 20:45
挂是挂上了可装配元件是报错请指教

作者: 177048139 时间: 2009-12-5 19:58
学习下学习下

作者: yinhengjia 时间: 2009-12-16 15:20
有没有EMX外挂

作者: hangtianxiao 时间: 2010-5-19 15:18
楼主啊
你真是个大大好人，好人定有丰厚回报
定会吉人天相。望楼主传份EMX4.1,我的QQ:290796481

作者: scolar 时间: 2010-7-26 13:58
已经挂上了谢谢！

作者: zjq1698 时间: 2010-11-7 10:43
有一点小问题，挂上两个后，两个同时用就不行，PROE关闭

作者: cdh.2007 时间: 2010-11-9 13:16
过来偷偷学一下！谢谢楼主，支持

作者: wild-boy 时间: 2010-12-1 11:03
支持，非常感谢。

作者: wjj007123 时间: 2011-4-1 09:40
老大，挂是挂上了，第一个问题，不出现瀑布式菜单，第二内部的模架全部是乱的！怎么回事？我仅仅挂的5.0

作者: daivenet 时间: 2011-4-2 15:55
下姐姐实际上加速拉升妈妈说了阿穆隆

作者: mik_sz 时间: 2011-4-7 19:13
都知道吹水，把东西传上来才是真英雄

作者: q48378185 时间: 2011-6-25 14:13
EMX的用处大吗?

作者: yuexiongmodel 时间: 2011-6-30 00:16

做个记号先，等慢再来学习

作者: 13554866369 时间: 2012-1-18 17:33
{:soso_e179:}

欢迎光临 iCAx开思网 (https://www.icax.org/)