iCAx开思网

标题: 请教 [打印本页]

作者: ggyggyggy 时间: 2009-7-13 15:22
标题: 请教
请问mastercam9.0走平行刀路后处理到法兰克机床上走时为什么段段续续？一点跑不快
？请教下，怎样才能让它跑快起来？

作者: kkndq 时间: 2009-7-13 15:39
你的程序传上来看一下

作者: ggyggyggy 时间: 2009-7-13 15:49
请看

(PROGRAM NAME - 11C2)
(DATE=DD-MM-YY - 13-07-09 TIME=HH:MM - 15:42)
(TOOL - 2 DIA. OFF. - 2 LEN. - 2 DIA. - 10.)
N100G91G28Z0
N102G0G90G54X97.128Y-14.668S2500M3
N104G43H2Z2.
N106Z-19.655
N108G1Z-21.655F1200.
N110X97.156Y-14.64Z-20.943F3000.
N112X97.157Y-14.639Z-20.932
N114X97.183Y-14.613
N116Z-20.929
N118X97.264Y-14.532Z-20.479
N120Z-20.198
N122X97.293Y-14.503Z-20.166
N124X97.326Y-14.47Z-20.153
N126X97.501Y-14.294Z-19.462
N128Z-19.438
N130X97.533Y-14.263Z-19.343
N132X98.06Y-13.736Z-19.384
N134X98.081Y-13.715Z-19.435
N136Z-19.44
N138X98.089Y-13.707
N140X98.306Y-13.49Z-20.154
N142X98.338Y-13.458Z-20.166
N144X98.367Y-13.429Z-20.198
N146Z-20.433
N148X98.462Y-13.334Z-20.917
N150X98.478Y-13.318Z-20.935
N152Z-21.094
N154X98.532Y-13.264Z-21.654
N156X98.534Y-13.262Z-21.656
N158X98.555Y-13.241Z-21.657
N160X98.564Y-13.231Z-22.149
N162X98.614Y-13.144
N164X98.643Y-13.094Z-22.139
N166Z-21.658
N168X98.66Y-13.063Z-21.651
N170X98.68Y-13.027Z-21.48
N172X98.721Y-12.955Z-21.625
N174X98.792Y-12.83Z-21.596
N176X98.886Y-12.665Z-21.658

作者: kkndq 时间: 2009-7-13 15:54
你想要多快啊?边传边做慢,还是程序再机床里都慢啊?

作者: ggyggyggy 时间: 2009-7-13 15:56
它是跑得慢。。。断断续续。在平点的地方就快点。。。一到斜坡就走不动了

作者: kkndq 时间: 2009-7-13 16:02
哦,我也遇到过这样的问题,我也是用9.0的,你看清楚一点,你机床断断续续时,肯定是你电脑传送程序不够快,意思就是机床在等电脑,正常要电脑等机床的,也或许你的机床有限,哎~~~反正有很多可能的,你自己看清楚一点吧

作者: kkndq 时间: 2009-7-13 16:33
朋友:搞定没有?如果没有搞定我就跟你说一下我以前是怎样搞定的,反正我今天有空,

作者: 利明 时间: 2009-7-14 17:22
机床的问题！
转角减速！！

欢迎光临 iCAx开思网 (https://www.icax.org/)