iCAx开思网

标题: CAM操作变换问题，恳请赐教！急！！！ [打印本页]

作者: hello_icax 时间: 2009-11-13 10:26
标题: CAM操作变换问题，恳请赐教！急！！！
本人想对某个操作进行两次变换。
先按某个轴旋转，然后以WCS原点作比例变换。
在GRIP中只要将两个变换矩阵相加即可。如下代码：
MAT1=MATRIX/ZXROT,30
MAT2=MATRIX/SCALE,1.2,1.2,1.2
MAT=MATRIX/MAT1,MAT2
OPTRAN/MAT,'R5_FSH',INSTNC,'AABBCC',30,IFERR,END1:

此代码可实现一次性变换。

现在，我想在vb.net中实现。
但我只能分两步实现。先旋转，再比例。
这样一来速度就慢了。

那位高手知道一步实现的方法。请赐教！谢谢！

作者: zhangcanwei 时间: 2009-11-13 17:44
你先把矩阵合并

作者: hello_icax 时间: 2009-11-14 08:40
谢谢2楼的热心。
但我是用的VB.NET开发，好像没用到矩阵。
代码如下：

Private Sub CopyThisOneOperation1(ByVal theSession As Session, ByVal stOper As String, _
         ByVal workPart As Part, ByVal nAng As Double, ByVal nScale As Double, ByVal stNewName As String)
      Dim objectsToTransform1(0) As CAM.CAMObject
      Dim operation1 As CAM.Operation = CType(workPart.CAMSetup.CAMOperationCollection.FindObject(stOper), CAM.Operation)
      objectsToTransform1(0) = operation1
      Dim operationTransformBuilder1 As CAM.OperationTransformBuilder
      operationTransformBuilder1 = workPart.CAMSetup.CreateOperationTransformBuilder(objectsToTransform1)
      operationTransformBuilder1.TransformType = CAM.OperationTransformBuilder.Transform.RotateAboutLine '+ CAM.OperationTransformBuilder.Transform.Scale
      operationTransformBuilder1.LineMethod = CAM.OperationTransformBuilder.Line.PointAndVector

      '旋转变换
      Dim op As Point3d = New Point3d(0, 0, 0)
      Dim point3 As NXOpen.Point
      point3 = workPart.Points.CreatePoint(op)
      operationTransformBuilder1.LinePoint = point3 '必须要此行
      Dim vec1 As Vector3d = New Vector3d(0, 1, 0)
      Dim direction1 As Direction
      direction1 = workPart.Directions.CreateDirection(op, vec1, SmartObject.UpdateOption.AfterModeling)
      operationTransformBuilder1.LineVector = direction1
      operationTransformBuilder1.MoveCopyInstance = CAM.OperationTransformBuilder.Result.Copy

      operationTransformBuilder1.NumOfCopyInstance = 1
      operationTransformBuilder1.AngleValue = nAng '旋转角度
      Dim nXObject2 As NXObject
      nXObject2 = operationTransformBuilder1.Commit()
      operationTransformBuilder1.Destroy()

      '比例变换
      Dim objects1(0) As CAM.CAMObject
      Dim operation2 As CAM.Operation
      operation2 = CType(workPart.CAMSetup.CAMOperationCollection.FindObject(stOper & "_COPY"), CAM.Operation)
      objectsToTransform1(0) = operation2
      operationTransformBuilder1 = workPart.CAMSetup.CreateOperationTransformBuilder(objectsToTransform1)
      operationTransformBuilder1.TransformType = CAM.OperationTransformBuilder.Transform.Scale
      operationTransformBuilder1.ReferencePoint = point3
      operationTransformBuilder1.MoveCopyInstance = CAM.OperationTransformBuilder.Result.Move '移动
      operationTransformBuilder1.ScaleFactor = nScale
      nXObject2 = operationTransformBuilder1.Commit()
      operationTransformBuilder1.Destroy()
      '比例变换完成！
      operation2.SetName(stNewName)

end sub

作者: zhangcanwei 时间: 2009-11-15 07:17
CreateTranslationMatrix () 用这个函数来连续变换矩阵

作者: zhangcanwei 时间: 2009-11-15 07:19
你这段代码好像是录制的，你可以先做两次变换后，再进行operationTransformBuilder1.Commit()

作者: hello_icax 时间: 2009-11-15 11:55
zhang兄,谢谢你的支持！
但还是搞不定。

第一，用UF函数好像不可对CAM对象进行变换。请看如下代码。
我运行后是失败的。
Private Sub TestTransform(ByVal workPart As Part, ByVal nAng As Double, ByVal nScale As Double)
      Dim se As UFSession = UFSession.GetUFSession()
      Dim obj1 As NXObject = Nothing
      Dim org(2) As Double '原点
      Dim dec(2) As Double '方向
      Dim mat(15) As Double '变换矩阵。
      Dim sta As Integer    '状态。
      org(0) = 0 : org(1) = 0 : org(2) = 0
      dec(0) = 0 : dec(1) = 1 : dec(2) = 0 '绕Y轴旋转角度nAng
      se.Trns.CreateRotationMatrix(org, dec, nAng, mat, sta)
      MsgBox(sta.ToString & mat.ToString) 'sta返回零表示成功。
      Dim operation1 As CAM.Operation = CType(workPart.CAMSetup.CAMOperationCollection.FindObject("CAM1"), CAM.Operation)
      Dim sTags(0) As NXOpen.Tag
      sTags(0) = operation1.Tag '下面的变换函数只能变换几何实体，不能变换CAM对象。不知为何。

      Dim tTags(0) As Tag
      Dim gTag As Tag
      Dim nCou As Integer
      MsgBox(sTags(0).ToString)
      nCou = 1 '指定变换数量。
      se.Trns.TransformObjects(mat, sTags, nCou, 2, -1, 2, tTags, gTag, sta)
      MsgBox(sta.ToString) '       3 - Invalid Object (Not Alive Or Not Transformable)
End Sub

函数TransformObjects的返回值sta=3。好像是说无效对象。这是否说明对CAM对象不支持？

第二，“先做两次变换，再commit()”，该如何实现?
请看下面的代码。
Private Sub CopyThisOneOperation1(ByVal theSession As Session, ByVal stOper As String, _
      ByVal workPart As Part, ByVal nAng As Double, ByVal nScale As Double, ByVal stNewName As String)
      Dim objectsToTransform1(0) As CAM.CAMObject
      Dim operation1 As CAM.Operation = CType(workPart.CAMSetup.CAMOperationCollection.FindObject(stOper), CAM.Operation)
      objectsToTransform1(0) = operation1
      Dim operationTransformBuilder1 As CAM.OperationTransformBuilder
      operationTransformBuilder1 = workPart.CAMSetup.CreateOperationTransformBuilder(objectsToTransform1)
      operationTransformBuilder1.TransformType = CAM.OperationTransformBuilder.Transform.RotateAboutLine
      '旋转变换
      operationTransformBuilder1.LineMethod = CAM.OperationTransformBuilder.Line.PointAndVector
      Dim op As Point3d = New Point3d(0, 0, 0)
      Dim point3 As NXOpen.Point
      point3 = workPart.Points.CreatePoint(op)
      operationTransformBuilder1.LinePoint = point3 '必须要此行
      Dim vec1 As Vector3d = New Vector3d(0, 1, 0)
      Dim direction1 As Direction
      direction1 = workPart.Directions.CreateDirection(op, vec1, SmartObject.UpdateOption.AfterModeling)
      operationTransformBuilder1.LineVector = direction1
      operationTransformBuilder1.NumOfCopyInstance = 1
      operationTransformBuilder1.AngleValue = nAng '旋转角度

      Dim nXObject2 As NXObject

      '比例变换
      operationTransformBuilder1.TransformType = CAM.OperationTransformBuilder.Transform.Scale
      operationTransformBuilder1.ReferencePoint = point3
      operationTransformBuilder1.MoveCopyInstance = CAM.OperationTransformBuilder.Result.Move '移动
      operationTransformBuilder1.ScaleFactor = nScale
      nXObject2 = operationTransformBuilder1.Commit()
      operationTransformBuilder1.Destroy()
      MsgBox("比例变换完成！")
      operation1.SetName(stNewName)
End Sub

我先指定变换方式为       operationTransformBuilder1.LineMethod = CAM.OperationTransformBuilder.Line.PointAndVector
然后不做operationTransformBuilder1.Commit()
指定变换方式为       operationTransformBuilder1.ScaleFactor = nScale

结果，是只进行了比例变换。
请您指教！谢谢！

作者: zhangcanwei 时间: 2009-11-15 12:55
1 我说的是变换矩阵，不是直接变换CAM操作。
2 我说的方法看来行不通。

这个方法100%可以：
operationTransformBuilder1.TransformType = CAM.OperationTransformBuilder.Transform.Reposition
然后设置operationTransformBuilder1.RepositionFromCsys
再设置 operationTransformBuilder1.RepositionToCsys

上面这两个Csys的设置应该不成问题吧

作者: hello_icax 时间: 2009-11-15 13:02
谢谢！容我研究一下！

作者: hello_icax 时间: 2009-11-15 13:11
zhang兄，请恕小弟愚笨。
1，用函数MultiplyMatrices()可以实现多个矩阵合并，但问题是：“函数TransformObjects的返回值sta=3。好像是说无效对象。这是否说明对CAM对象不支持？”

2，RepositionFromCsys只是方位变换，而我还要比例变换！

欢迎光临 iCAx开思网 (https://www.icax.org/)