iCAx开思网

标题: 【求助】关于刀具半径补偿！！！ [打印本页]

作者: xianglong 时间: 2003-6-24 13:34
标题: 【求助】关于刀具半径补偿！！！
我用ug做了一个车削程序，其中精车段的程序如下：%
O0001
G00 X100. Z100.
X40.673 Z22.074
G02 X41.578 Z19.823 I2.944 K-.579 F1.
G03 X49.687 Z9.346 I-21.189 K-14.223
G03 X49.7 Z9.258 I-.594 K-.088
G01 Z1.927
G40 X55.7
G00 X100. Z100.
我在后处理时用的刀具的刀尖半径是0.4，刀具象限位是3，在ug处理时已经进行了刀尖补偿。但我不知道怎样才能当刀尖磨损时，圆弧面增大，如何对其进行补偿，以满足尺寸要求！

作者: xianglong 时间: 2003-6-24 13:49
我用ug做了一个车削程序，
%
O0001
N10G97S600M03
T0101
M08
G00X100.Z60.
X0.
Z25.
G01Z-8.F0.2
G00Z25.
G01Z60.F0.5
M09
M05
T0100
G00X100.Z100.
/M01
N20G97S800M04
T0202
M08
G00X60.Z60.
X53.138Z21.8
G01Z21.F0.5
Z2.627F0.3
X56.
X57.131Z3.193F0.5
G00Z21.8
X50.276
G01Z21.
Z9.034F0.3
X50.3Z8.954
Z2.627
X53.138
X54.27Z3.193F0.5
G00Z21.8
X46.295
G01Z21.
Z15.877F0.3
G03X50.276Z9.034I-23.948K-10.677
G01X51.408Z9.6F0.5
G00Z21.566
X43.445
G01X42.314Z21.
Z19.531F0.3
G03X46.295Z15.877I-21.957K-14.331
G01X47.427Z16.443F0.5
G00X60.Z60.
M05
M09
T0200
G00X100.Z100.
/M01
N30G97S1000M04
T0303
M08
G00X60.Z60.
X43.445Z20.566
G01X42.314Z20.
X26.8F0.1
X25.2F0.5
G00X60.Z60.
M05
M09
T0300
G00X100.Z100.
/M01
N40G97S800M04
T0404
M08
X28.Z60.
X30.869Z20.566
G01X32.Z20.
Z2.F0.15
X30.
X28.869Z2.566F0.5
G00X28.Z60.
M05
M09
T0400
G00X100.Z100.
/M01
N50G97S1000M04(精车段)
T0505
M08
G00X40.Z60.
X40.673Z22.074
G02X41.578Z19.823I2.944K-.579F0.2
G03X49.687Z9.346I-21.189K-14.223F0.1
G03X49.7Z9.258I-.594K-.088
G01Z1.927
X55.7F0.2
G00X70.Z60.
M05
M09
T0500
G00X100.Z100.
/M01
N60G97S1000M04
T0606
M08
G00X60.Z6.
X57.7Z6.
G01X49.8F0.5
X32.F0.06
G00X32.9
X60.
M05
M09
T0600
G00X100.Z100.
M30

我在N50精车段后处理时用的刀具的刀尖半径是0.4，刀具象限位是3，由于ug处理时已经进行了刀尖补偿（G42补偿）因而我不知道怎样才能当刀尖磨损时，圆弧面增大，如何对其进行补偿，（补偿刀尖半径磨损值没有用）,以满足尺寸要求！：（
要让程序中生成G41,G42,那么如何设置刀具的象限位，使刀轨路径正确！：（

作者: xianglong 时间: 2003-6-26 23:08
虽然没有人回应我！我还是解决了：）

作者: z_ty1987 时间: 2013-9-22 22:37
支持楼主分享了啊，赞一个！！

欢迎光临 iCAx开思网 (https://www.icax.org/)