iCAx开思网

标题: 关于.nc和.tap。是怎么转换？ [打印本页]

作者: 837298328 时间: 2010-6-9 10:47
标题: 关于.nc和.tap。是怎么转换？
我这里有一台CNC，现在只能走.TAP的程序。.NC不能用，请问mc有没有后处理出来是.TAP的后处理。或者要怎么改？

作者: ppen 时间: 2010-6-9 20:07
# General Output Settings
# --------------------------------------------------------------------------
spaces    : 1    #Number of spaces to add between fields
omitseq    : yes #Omit sequence numbers?
seqmax    : 9999  #Max. sequence number
arcoutput : 0    #0 = IJK, 1 = R no sign, 2 = R signed neg. over 180
arctype    : 2    #Arc center 1=abs, 2=St-Ctr, 3=Ctr-St, 4=unsigned inc.
breakarcs : 2    #Break arcs, 0 = no, 1 = quadrants, 2 = 180deg. max arcs
do_full_arc : 0    #Allow full circle output? 0=no, 1=yes
helix_arc : 0    #Support helix arc output, 0=no, 1=all planes, 2=XY plane only
compwarn : 1    #Warn if cutter comp applied on arc, 0=no, 1=yes
miscerror : 0    #Error out if Misc Values button is disabled, 0=no, 1=yes
maxrad    : 999 #Maximum arc radius
hel_2100 : no #Acramatic 2100 style helical moves, 0=no, 1=yes
usecanned : yes #Use canned drilling cycles?  Set to no for long output.
force_dpts  : no #Force XY output on all drilling lines including cycle call?
haas_drill  : 0    #Haas style peck drill, 0=no, 1=yes
wcstype    : 2    #0 = G92 at start, 1 = G92 at toolchanges, 2 = G54, 3 = Off
force_wcs : yes #Force WCS output at every toolchange?
stagetool : 0    #0 = Do not pre-stage tools, 1 = Stage tools
tool_table  : 1    #Tool table, 0=no, 1=yes, 2=Predator VCNC, 3=MetaCut View
output_z : yes #Output Z Min and Z Max values (yes or no)
cool_zmove  : yes #Coolant off with last move
use_pitch : 0    #0 = Use feed for tapping, 1 = Use pitch for tapping
tap_feed : 0    #0 = 2/1 (in/mm) decimal places, 1 = 4/3 (in/mm) decimal places
maxfeedpm : 500 #Limit for feed in inch/min
maxfeedpm_m : 10000 #Limit for feed in mm/min
use_gear : 0    #Output gear selection code, 0=no, 1=yes
max_speed : 10000 #Maximum spindle speed
min_speed : 50 #Minimum spindle speed
sextnc    .NC    #NC extension override    把前面.NC改成你想要的.TAP，如果没有这一行请加入。

作者: liangchang197 时间: 2010-6-17 10:11
点文件属性将TAP改成NC皆可

作者: wowoyuansl 时间: 2010-6-17 21:14
提示: 作者被禁止或删除内容自动屏蔽

作者: 1138587825 时间: 2015-7-30 12:48

wowoyuansl 发表于 2010-6-17 21:14
**** 作者被禁止或删除内容自动屏蔽 ****

要改后缀名

欢迎光临 iCAx开思网 (https://www.icax.org/)