iCAx开思网

标题: 后处理问题 [打印本页]

作者: make116 时间: 2010-9-27 09:52
标题: 后处理问题
请高手帮忙改一下！小弟在此谢过！

把程序
%
(T= DIA=6. R=0. H=0 D=0)
G40G80G17
G49
G91G28Z0.
S12000M3
G90G00
G0X3.Y3.
G43Z10.
Z0.
G1Z-5.F50.
X197.F800.
Y6.
X3.
Y9.
X197.
Y12.
X3.
Y15.
X197.
Y18.
X3.
Y21.
X197.
Y24.
X3.
Y27.
X197.
Y30.
X3.
Y33.
X197.
Y36.
X3.
Y39.
X197.
Y42.
X3.
Y45.
X197.
Y48.
X3.
Y51.
X197.
Y54.
X3.
Y57.
X197.
Y60.
X3.
Y63.
X197.
Y66.
X3.
Y69.
X197.
Y72.
X3.
Y75.
X197.
Y78.
X3.
Y81.
X197.
Y84.
X3.
Y87.
X197.
Y90.
X3.
Y93.
X197.
Y96.
X3.
Y99.
X197.
Y102.
X3.
Y105.
X197.
Y108.
X3.
Y111.
X197.
Y114.
X3.
Y117.
X197.
Y120.
X3.
Y123.
X197.
Y126.
X3.
Y129.
X197.
Y132.
X3.
Y135.
X197.
Y138.
X3.
Y141.
X197.
Y144.
X3.
Y147.
X197.
Y150.
X3.
Y153.
X197.
Y156.
X3.
Y159.
X197.
Y162.
X3.
Y165.
X197.
Y168.
X3.
Y171.
X197.
Y174.
X3.
Y177.
X197.
Y180.
X3.
Y183.
X197.
Y186.
X3.
Y189.
X197.
Y192.
X3.
Y195.
X197.
Y198.
X3.
Y201.
X197.
Y204.
X3.
Y207.
X197.
Y210.
X3.
Y213.
X197.
Y216.
X3.
Y219.
X197.
Y222.
X3.
Y225.
X197.
Y228.
X3.
Y231.
X197.
Y234.
X3.
Y237.
X197.
Y240.
X3.
Y243.
X197.
Y246.
X3.
Y249.
X197.
Y252.
X3.
Y255.
X197.
Y258.
X3.
Y261.
X197.
Y264.
X3.
Y267.
X197.
Y270.
X3.
Y273.
X197.
Y276.
X3.
Y279.
X197.
Y282.
X3.
Y285.
X197.
Y288.
X3.
Y291.
X197.
Y294.
X3.
Y297.
X197.
G0Z10.
M05
G91G28Z0.
G28Y0.
G29X0.
M30
%
改成
T0 ([平底]JD-6.00)
G0X3.Y3.Z10.000
Z0.
G1Z-5.F50.
X197.F800.
Y6.
X3.
Y9.
X197.
Y12.
X3.
Y15.
X197.
Y18.
X3.
Y21.
X197.
Y24.
X3.
Y27.
X197.
Y30.
X3.
Y33.
X197.
Y36.
X3.
Y39.
X197.
Y42.
X3.
Y45.
X197.
Y48.
X3.
Y51.
X197.
Y54.
X3.
Y57.
X197.
Y60.
X3.
Y63.
X197.
Y66.
X3.
Y69.
X197.
Y72.
X3.
Y75.
X197.
Y78.
X3.
Y81.
X197.
Y84.
X3.
Y87.
X197.
Y90.
X3.
Y93.
X197.
Y96.
X3.
Y99.
X197.
Y102.
X3.
Y105.
X197.
Y108.
X3.
Y111.
X197.
Y114.
X3.
Y117.
X197.
Y120.
X3.
Y123.
X197.
Y126.
X3.
Y129.
X197.
Y132.
X3.
Y135.
X197.
Y138.
X3.
Y141.
X197.
Y144.
X3.
Y147.
X197.
Y150.
X3.
Y153.
X197.
Y156.
X3.
Y159.
X197.
Y162.
X3.
Y165.
X197.
Y168.
X3.
Y171.
X197.
Y174.
X3.
Y177.
X197.
Y180.
X3.
Y183.
X197.
Y186.
X3.
Y189.
X197.
Y192.
X3.
Y195.
X197.
Y198.
X3.
Y201.
X197.
Y204.
X3.
Y207.
X197.
Y210.
X3.
Y213.
X197.
Y216.
X3.
Y219.
X197.
Y222.
X3.
Y225.
X197.
Y228.
X3.
Y231.
X197.
Y234.
X3.
Y237.
X197.
Y240.
X3.
Y243.
X197.
Y246.
X3.
Y249.
X197.
Y252.
X3.
Y255.
X197.
Y258.
X3.
Y261.
X197.
Y264.
X3.
Y267.
X197.
Y270.
X3.
Y273.
X197.
Y276.
X3.
Y279.
X197.
Y282.
X3.
Y285.
X197.
Y288.
X3.
Y291.
X197.
Y294.
X3.
Y297.
X197.
G0Z10.
各位大侠如能帮忙感激不尽。再次谢过。

作者: make116 时间: 2010-9-27 09:57
主要是改一下后处理的头和尾。再次谢谢大家能帮助我。我在补充一下我用的软件是mstercam9.1版本的

本帖最后由 make116 于 2010-9-27 10:03 编辑

欢迎光临 iCAx开思网 (https://www.icax.org/)