iCAx开思网

标题: 后处理高手请问 [打印本页]

作者: pd05 时间: 2011-2-22 22:28
标题: 后处理高手请问
请帮忙改后处理。
要求M08T1改成
M08
T1
也就是备刀要例起一行，不能跟在M08后面

%
O0001
( PROGRAM - TTT.NC)
( DATE    - FEB-22-11)
( TIME    - 20:12)
( MC9 FILE  - C:\DOCUMENTS AND SETTINGS\ADMINISTRATOR\桌面\TTT.MC9)
( --------------------------------------------- )
(T1 | H1 | D10.00mm |    |A90.       |2D-CONTOUR )
(T2 | H2 | D5.00mm  |    |A90.       |2D-CONTOUR )
( --------------------------------------------- )
( ------------------- OVERALL MAX - Z10. )
( ------------------- OVERALL MIN - Z-2. )
N100 G00 G17 G21 G40 G80 G90
( T1 ----- 2D-CONTOUR  )
N102 T1 M06 (DEFINE TOOL NAMES)
N104 (MAX - Z10.)
N106 (MIN - Z-1.)
N108 (CUT STOCK: XY= 0.000 Z = 0.000)
N110 G00 G90 G54 X.25 Y-18. S1100 M03
N112 G43 H1 Z10. M08 T2
N114 Z1.
N116 G01 Z-1. F1000.
N118 Y-17.75
N120 G03 X0. Y-17.5 I-.25 J0.
N122 G01 X-25.
N124 G02 X-30. Y-12.5 I0. J5.
N126 G01 Y12.5
N128 G02 X-25. Y17.5 I5. J0.
N130 G01 X25.
N132 G02 X30. Y12.5 I0. J-5.
N134 G01 Y-12.5
N136 G02 X25. Y-17.5 I-5. J0.
N138 G01 X0.
N140 X-2.
N142 G03 X-2.25 Y-17.75 I0. J-.25
N144 G01 Y-18.
N146 Z0.
N148 G00 Z10. M09
N150 M05
N152 G91 G28 Z0.
N154 M01
( T2 ----- 2D-CONTOUR  )
N156 T2 M06 (DEFINE TOOL NAMES)
N158 (MAX - Z10.)
N160 (MIN - Z-2.)
N162 (CUT STOCK: XY= 0.000 Z = 0.000)
N164 G00 G90 G54 X.125 Y-15.25 S1000 M03
N166 G43 H2 Z10. M08 T1
N168 Z1.
N170 G01 Z-2. F1000.
N172 Y-15.125
N174 G03 X0. Y-15. I-.125 J0.
N176 G01 X-25.
N178 G02 X-27.5 Y-12.5 I0. J2.5
N180 G01 Y12.5
N182 G02 X-25. Y15. I2.5 J0.
N184 G01 X25.
N186 G02 X27.5 Y12.5 I0. J-2.5
N188 G01 Y-12.5
N190 G02 X25. Y-15. I-2.5 J0.
N192 G01 X0.
N194 X-2.
N196 G03 X-2.125 Y-15.125 I0. J-.125
N198 G01 Y-15.25
N200 Z-1.
N202 G00 Z10. M09
N204 M05
N206 G91 G28 Z0.
N208 G28 X0. Y0.
N210 G90
N212 M30
%

作者: bolimo 时间: 2011-2-23 16:43
1# pd05 很简单~~~
%
O0001
( PROGRAM - TTT.NC)
( DATE    - FEB-23-11)
( TIME    - 16:40)
( MC9 FILE  - F:\新建文件夹 (2)\TTT.MC9)
( --------------------------------------------- )
(T1 | H1 | D10.00mm |    |A90.       |2D-CONTOUR )
(T2 | H2 | D5.00mm  |    |A90.       |2D-CONTOUR )
( --------------------------------------------- )
( ------------------- OVERALL MAX - Z10. )
( ------------------- OVERALL MIN - Z-2. )
N100 G00 G17 G21 G40 G80 G90
( T1 ----- 2D-CONTOUR  )
N102 T1 M06 (DEFINE TOOL NAMES)
N104 (MAX - Z10.)
N106 (MIN - Z-1.)
N108 (CUT STOCK: XY= 0.000 Z = 0.000)
N110 G00 G90 G54 X.25 Y-18. S1100 M03
N112 G43 H1 Z10. M08
N114 T2
N116 Z1.
N118 G01 Z-1. F1000.
N120 Y-17.75
N122 G03 X0. Y-17.5 I-.25 J0.
N124 G01 X-25.
N126 G02 X-30. Y-12.5 I0. J5.
N128 G01 Y12.5
N130 G02 X-25. Y17.5 I5. J0.
N132 G01 X25.
N134 G02 X30. Y12.5 I0. J-5.
N136 G01 Y-12.5
N138 G02 X25. Y-17.5 I-5. J0.
N140 G01 X0.
N142 X-2.
N144 G03 X-2.25 Y-17.75 I0. J-.25
N146 G01 Y-18.
N148 Z0.
N150 G00 Z10. M09
N152 M05
N154 G91 G28 Z0.
N156 M01
( T2 ----- 2D-CONTOUR  )
N158 T2 M06 (DEFINE TOOL NAMES)
N160 (MAX - Z10.)
N162 (MIN - Z-2.)
N164 (CUT STOCK: XY= 0.000 Z = 0.000)
N166 G00 G90 G54 X.125 Y-15.25 S1000 M03
N168 G43 H2 Z10. M08
N170 T1
N172 Z1.
N174 G01 Z-2. F1000.
N176 Y-15.125
N178 G03 X0. Y-15. I-.125 J0.
N180 G01 X-25.
N182 G02 X-27.5 Y-12.5 I0. J2.5
N184 G01 Y12.5
N186 G02 X-25. Y15. I2.5 J0.
N188 G01 X25.
N190 G02 X27.5 Y12.5 I0. J-2.5
N192 G01 Y-12.5
N194 G02 X25. Y-15. I-2.5 J0.
N196 G01 X0.
N198 X-2.
N200 G03 X-2.125 Y-15.125 I0. J-.125
N202 G01 Y-15.25
N204 Z-1.
N206 G00 Z10. M09
N208 M05
N210 G91 G28 Z0.
N212 G28 X0. Y0.
N214 G90
N216 M30
%
附件里是我改好的后处理，你这个床子我以前没见过，求解释为啥t1刚开始跑，t2在程序段中的作用

本帖最后由 bolimo 于 2011-2-23 16:46 编辑

作者: sz984137 时间: 2011-2-23 23:30
谢谢两楼bolimo ，T2是备刀用的

作者: desk121 时间: 2011-2-24 12:56
next_tool 參數
另起一行即可解決樓主之困惑。

很多機器如果遇到T命令，直接換刀了。這個備用預選刀在什麽機床什麽系統上用到

本帖最后由 desk121 于 2011-2-24 12:58 编辑

作者: ss1268 时间: 2011-2-25 07:49
现在的toyoda,老的30,和大卫的机器是这种格式.

欢迎光临 iCAx开思网 (https://www.icax.org/)