iCAx开思网

标题: mastercam x5 立式车后处理 [打印本页]

作者: zgy850108 时间: 2012-4-13 10:13
标题: mastercam x5 立式车后处理
求的mastercam x5 立式车后处理法拉克系统的，只有X,Z,C三个轴的！我有个后处理，但后处理出来的程序好像有点问题，
%
O0000
(PROGRAM NAME - TT)
(DATE=DD-MM-YY - 13-04-12 TIME=HH:MM - 09:54)
(MCX FILE - D:\我的文档\MY MCAMX5\MCX\T.MCX-5)
(NC FILE - D:\我的文档\MY MCAMX5\LATHE\NC\TT.NC)
(MATERIAL - ALUMINUM MM - 2024)
G21
(TOOL - 1 OFFSET - 1)
(T0101-WORK FACE  INSERT - CNMG-643)
( T0101 FACING )
T0101 M06
G18
G97 S200 M03
G0 G55 X292.814 Z0.
G50 S200
G96 S185
G99 G1 X-4.381 F.5
G0 Z2.
G28 W0. M05
M09
M01
(TOOL - 18 OFFSET - 18)
(T0404-OD ROUGH  INSERT - CNMG-643)
( T1818 ROUGH OD )
T1818 M06
G18
G97 S257 M03
G0 G55 X285.215 Z4.5
G50 S500
G96 S230
G1 Z2.5 F.5
Z-20.204
G18 G3 X289.214 Z-23.886 R4.391
G1 Z-50.371
X292.042 Z-48.957
G0 Z4.5
X281.217
G1 Z2.5
Z-19.513
G3 X285.615 Z-20.342 R4.391
G1 X288.444 Z-18.927
G0 Z4.5
X277.218
G1 Z2.5
Z-19.495
X280.432
G3 X281.617 Z-19.535 R4.391
G1 X284.445 Z-18.121
G0 Z4.5
X273.22
G1 Z2.5
Z-19.495
X277.618
X280.447 Z-18.081
G0 Z4.5
X269.221
G1 Z2.5
Z-19.495
X273.62
X276.448 Z-18.081
G0 Z4.5
X265.223
G1 Z2.5
Z-19.495
X269.621
X272.45 Z-18.081
G0 Z4.5
X261.225
G1 Z2.5
Z-19.495
X265.623
X268.451 Z-18.081
G0 Z4.5
X257.226
G1 Z2.5
Z-19.495
X261.625
X264.453 Z-18.081
G0 Z4.5
X253.228
G1 Z2.5
Z-19.495
X257.626
X260.455 Z-18.081
G0 Z4.5
X249.229
G1 Z2.5
Z-19.495
X253.628
X256.456 Z-18.081
G0 Z4.5
X245.231
G1 Z2.5
Z-19.495
X249.629
X252.458 Z-18.081
G0 Z4.5
X241.232
G1 Z2.5
Z-19.495
X245.631
X248.459 Z-18.081
G0 Z4.5
X237.234
G1 Z2.5
Z-19.495
X241.632
X244.461 Z-18.081
G0 Z4.5
X233.235
G1 Z2.5
Z-19.495
X237.634
X240.462 Z-18.081
G0 Z4.5
X229.237
G1 Z2.5
Z-19.495
X233.635
X236.464 Z-18.081
G0 Z4.5
X225.239
G1 Z2.5
Z-19.495
X229.637
X232.465 Z-18.081
G0 Z4.5
X221.24
G1 Z2.5
Z-19.495
X225.639
X228.467 Z-18.081
G0 Z4.5
X217.242
G1 Z2.5
Z-19.495
X221.64
X224.469 Z-18.081
G0 Z4.5
X213.243
G1 Z2.5
Z-19.495
X217.642
X220.47 Z-18.081
G0 Z4.5
X209.245
G1 Z2.5
Z-19.495
X209.249
X213.643
X216.472 Z-18.081
G0 Z4.5
X205.246
G1 Z2.5
Z-2.377
G3 X206.031 Z-4.191 R4.391
G1 Z-17.886
G2 X209.249 Z-19.495 R1.609
G1 X209.645
X212.473 Z-18.081
G0 Z4.5
X201.248
G1 Z2.5
Z-.282
G3 X205.646 Z-2.906 R4.391
G1 X208.475 Z-1.492
G0 Z4.7
X197.249
G1 Z2.7
Z.2
G3 X201.648 Z-.39 R4.391
G1 X204.476 Z1.024
G28 W0. M05
M09
M01
(TOOL - 5 OFFSET - 5)
(T0505-OD FINISH  INSERT - CNMG-643)
( T0505 FINISHING OD )
T0505 M06
G18
G97 S403 M03
G0 G55 X197.249 Z2.
G50 S500
G96 S250
G1 Z0. F.5
G18 G3 X205.631 Z-4.191 R4.191
G1 Z-17.886
G2 X209.249 Z-19.695 R1.809
G1 X280.432
G3 X288.814 Z-23.886 R4.191
G1 Z-49.18
X291.642 Z-47.766
G28 W0. M05
M09
M30
%
有没有高人能指点下，红色标识的是、地方好像有点本末倒置了，G97怎么先取消了圆周速度恒定控制呢？然后又设定G50最大转速，最后又设定G96恒定圆周转速？是不是要改下，改哪里，后处理打开我看到傻了，全乱了，以前没改过！跪求帮助！

作者: yszwx 时间: 2012-4-17 10:27
dddddddddddddddddddddddddddddddddd

作者: hsmtool 时间: 2012-4-18 23:09
DDDDDDDDDDDDDDDDDDDDDDDD

作者: hsmtool 时间: 2012-4-18 23:12

hsmtool 发表于 2012-4-18 23:09
DDDDDDDDDDDDDDDDDDDDDDDD

oooooooooooooo

作者: hsmtool 时间: 2012-4-18 23:12

hsmtool 发表于 2012-4-18 23:12
oooooooooooooo

ppppppppppppppppp

作者: hsmtool 时间: 2012-4-18 23:14

hsmtool 发表于 2012-4-18 23:12
ppppppppppppppppp

aaaaaaaaaaaa

作者: 万金婵 时间: 2012-4-18 23:14
顶顶顶顶顶顶顶顶顶顶

欢迎光临 iCAx开思网 (https://www.icax.org/)