iCAx开思网

标题: 斜面上进行拐角加工 [打印本页]

作者: bin2708011 时间: 2012-5-14 15:25
标题: 斜面上进行拐角加工
上面是加工的仿真截图，下面是用机床生成的加工程序，程序里面那个DOWN STEP后面的是空的，用思美创这个软件就行斜面上的加工，那个切削深度应该怎么设定我的程序现在是这样的看看有什么需要修改的

0 BEGIN PGM 1000 MM
1 BLK FORM 0.1 Z X+0 Y+0 Z+0
2 BLK FORM 0.2 X+0 Y+0 Z+0
3 CYCL DEF 7.1  #1
4 CYCL DEF 7.0 DATUM SHIFT
5 CYCL DEF 7.1  X+0
6 CYCL DEF 7.2  Y+0
7 CYCL DEF 7.3  Z+0
8 CYCL DEF 32.0 TOLERANCE
9 CYCL DEF 32.1 T0.005
10 M109
11 TOOL CALL 03 Z S10000 M04
12 ;(BALL04-H  D = +4 R = +2 )
13 ;(  CONT. OFFSET= 0.0  CONT. TOL.= +0.001 )
14 ;(  SRF. OFFSET= -0.1 SRF. TOL.= +0.001 )
15 ;(  DOWN STEP= SIDE STEP= +0.5 )
16 L X0. Y0. FMAX
17 M07
18 L X+3.84 Y+10.065 Z+30 FMAX
19 L Z+7.005 FMAX
20 L Z+6.005 F240
21 L X+1.84 F800
22 L Y+40.263 Z+23.44
23 L X+27.005 Y+2.516 Z+1.646 F400
24 L X+1.84 F800
25 L Y+10.065 Z+6.005
26 L X+3.84
27 L X+2.34 Y+10.121 Z+6.037 F320
28 L Y+38.611 Z+22.486 F800
29 L X+26.07 Y+3.016 Z+1.935 F400
30 L X+2.34 F800
31 L Y+10.121 Z+6.037
32 L X+2.84 Y+10.177 Z+6.07 F320
33 L Y+36.96 Z+21.533 F800
34 L X+25.136 Y+3.516 Z+2.224 F400
35 L X+2.84 F800
36 L Y+10.177 Z+6.07
37 L X+3.34 Y+10.233 Z+6.102 F320
38 L Y+35.309 Z+20.579 F800
39 L X+24.202 Y+4.016 Z+2.512 F400
40 L X+3.34 F800
41 L Y+10.233 Z+6.102
42 L X+3.84 Y+10.289 Z+6.134 F320
43 L Y+33.657 Z+19.626 F800
44 L X+23.267 Y+4.516 Z+2.801 F400
45 L X+3.84 F800
46 L Y+10.289 Z+6.134
47 L X+4.34 Y+10.345 Z+6.166 F320
48 L Y+32.006 Z+18.673 F800
49 L X+22.333 Y+5.016 Z+3.09 F400
50 L X+4.34 F800
51 L Y+10.345 Z+6.166
52 L X+4.84 Y+10.401 Z+6.199 F320
53 L Y+30.355 Z+17.719 F800
54 L X+21.399 Y+5.516 Z+3.378 F400
55 L X+4.84 F800
56 L Y+10.401 Z+6.199
57 L X+5.34 Y+10.457 Z+6.231 F320
58 L Y+28.703 Z+16.766 F800
59 L X+20.465 Y+6.016 Z+3.667 F400
60 L X+5.34 F800
61 L Y+10.457 Z+6.231
62 L X+5.84 Y+10.512 Z+6.263 F320
63 L Y+27.052 Z+15.812 F800
64 L X+19.53 Y+6.516 Z+3.956 F400
65 L X+5.84 F800
66 L Y+10.512 Z+6.263
67 L X+6.34 Y+10.568 Z+6.296 F320
68 L Y+25.4 Z+14.859 F800
69 L X+18.596 Y+7.016 Z+4.244 F400
70 L X+6.34 F800
71 L Y+10.568 Z+6.296
72 L X+6.84 Y+10.624 Z+6.328 F320
73 L Y+23.749 Z+13.905 F800
74 L X+17.662 Y+7.516 Z+4.533 F400
75 L X+6.84 F800
76 L Y+10.624 Z+6.328
77 L X+7.34 Y+10.68 Z+6.36 F320
78 L Y+22.098 Z+12.952 F800
79 L X+16.728 Y+8.016 Z+4.822 F400
80 L X+7.34 F800
81 L Y+10.68 Z+6.36
82 L X+7.84 Y+10.736 Z+6.392 F320
83 L Y+20.446 Z+11.999 F800
84 L X+15.793 Y+8.516 Z+5.11 F400
85 L X+7.84 F800
86 L Y+10.736 Z+6.392
87 L X+8.34 Y+10.792 Z+6.425 F320
88 L Y+18.795 Z+11.045 F800
89 L X+14.859 Y+9.016 Z+5.399 F400
90 L X+8.34 F800
91 L Y+10.792 Z+6.425
92 L X+8.84 Y+10.848 Z+6.457 F320
93 L Y+17.143 Z+10.092 F800
94 L X+13.925 Y+9.516 Z+5.688 F400
95 L X+8.84 F800
96 L Y+10.848 Z+6.457
97 L X+9.34 Y+10.904 Z+6.489 F320
98 L Y+15.492 Z+9.138 F800
99 L X+12.991 Y+10.016 Z+5.976 F400
100 L X+9.34 F800
101 L Y+10.904 Z+6.489
102 L X+9.84 Y+10.96 Z+6.522 F320
103 L Y+13.841 Z+8.185 F800
104 L X+12.056 Y+10.516 Z+6.265 F400
105 L X+9.84 F800
106 L Y+10.96 Z+6.522
107 L X+10.34 Y+11.016 Z+6.554 F320
108 L Y+12.189 Z+7.231 F800
109 L X+11.122 Y+11.016 Z+6.554 F400
110 L X+10.34 F800
111 L Z+30 FMAX
112 L X+24.173 Y+16.116 FMAX
113 L Z+10.498 FMAX
114 L Z+9.498 F240
115 L X+22.509 Y+15.006 Z+8.858 F400
116 L X+5.671 Y+40.263 Z+23.44 F800
117 L X+30.836
118 L Y+2.516 Z+1.646 F400
119 L X+22.509 Y+15.006 Z+8.858 F800
120 L X+24.173 Y+16.116 Z+9.498
121 L X+22.499 Y+15.923 Z+9.387 F320
122 L X+6.606 Y+39.763 Z+23.151 F800
123 L X+30.336
124 L Y+4.167 Z+2.6 F400
125 L X+22.499 Y+15.923 Z+9.387 F800
126 L X+22.489 Y+16.84 Z+9.916 F320
127 L X+7.54 Y+39.263 Z+22.862 F800
128 L X+29.836
129 L Y+5.819 Z+3.553 F400
130 L X+22.489 Y+16.84 Z+9.916 F800
131 L X+22.479 Y+17.756 Z+10.446 F320
132 L X+8.474 Y+38.763 Z+22.574 F800
133 L X+29.336
134 L Y+7.47 Z+4.507 F400
135 L X+22.479 Y+17.756 Z+10.446 F800
136 L X+22.469 Y+18.673 Z+10.975 F320
137 L X+9.409 Y+38.263 Z+22.285 F800
138 L X+28.836
139 L Y+9.121 Z+5.46 F400
140 L X+22.469 Y+18.673 Z+10.975 F800
141 L X+22.458 Y+19.59 Z+11.504 F320
142 L X+10.343 Y+37.763 Z+21.996 F800
143 L X+28.336
144 L Y+10.773 Z+6.414 F400
145 L X+22.458 Y+19.59 Z+11.504 F800
146 L X+22.448 Y+20.506 Z+12.033 F320
147 L X+11.277 Y+37.263 Z+21.708 F800
148 L X+27.836
149 L Y+12.424 Z+7.367 F400
150 L X+22.448 Y+20.506 Z+12.033 F800
151 L X+22.438 Y+21.423 Z+12.562 F320
152 L X+12.211 Y+36.763 Z+21.419 F800
153 L X+27.336
154 L Y+14.076 Z+8.32 F400
155 L X+22.438 Y+21.423 Z+12.562 F800
156 L X+22.428 Y+22.34 Z+13.092 F320
157 L X+13.146 Y+36.263 Z+21.13 F800
158 L X+26.836
159 L Y+15.727 Z+9.274 F400
160 L X+22.428 Y+22.34 Z+13.092 F800
161 L X+22.418 Y+23.256 Z+13.621 F320
162 L X+14.08 Y+35.763 Z+20.842 F800
163 L X+26.336
164 L Y+17.378 Z+10.227 F400
165 L X+22.418 Y+23.256 Z+13.621 F800
166 L X+22.408 Y+24.173 Z+14.15 F320
167 L X+15.014 Y+35.263 Z+20.553 F800
168 L X+25.836
169 L Y+19.03 Z+11.181 F400
170 L X+22.408 Y+24.173 Z+14.15 F800
171 L X+22.397 Y+25.09 Z+14.679 F320
172 L X+15.948 Y+34.763 Z+20.264 F800
173 L X+25.336
174 L Y+20.681 Z+12.134 F400
175 L X+22.397 Y+25.09 Z+14.679 F800
176 L X+22.387 Y+26.006 Z+15.209 F320
177 L X+16.883 Y+34.263 Z+19.976 F800
178 L X+24.836
179 L Y+22.333 Z+13.088 F400
180 L X+22.387 Y+26.006 Z+15.209 F800
181 L X+22.377 Y+26.923 Z+15.738 F320
182 L X+17.817 Y+33.763 Z+19.687 F800
183 L X+24.336
184 L Y+23.984 Z+14.041 F400
185 L X+22.377 Y+26.923 Z+15.738 F800
186 L X+22.367 Y+27.84 Z+16.267 F320
187 L X+18.751 Y+33.263 Z+19.398 F800
188 L X+23.836
189 L Y+25.635 Z+14.994 F400
190 L X+22.367 Y+27.84 Z+16.267 F800
191 L X+22.357 Y+28.756 Z+16.796 F320
192 L X+19.685 Y+32.763 Z+19.11 F800
193 L X+23.336
194 L Y+27.287 Z+15.948 F400
195 L X+22.357 Y+28.756 Z+16.796 F800
196 L X+22.346 Y+29.673 Z+17.326 F320
197 L X+20.62 Y+32.263 Z+18.821 F800
198 L X+22.836
199 L Y+28.938 Z+16.901 F400
200 L X+22.346 Y+29.673 Z+17.326 F800
201 L X+22.336 Y+30.589 Z+17.855 F320
202 L X+21.554 Y+31.763 Z+18.532 F800
203 L X+22.336
204 L Y+30.589 Z+17.855 F400
205 L Z+30 FMAX
206 M111
207 M30
208 END PGM 1000 MM

作者: 开动脑筋深思 时间: 2012-5-14 16:00
啥高科技呀看不懂

作者: lai8222122 时间: 2012-5-14 17:05
真的看不懂

作者: 死神-死神 时间: 2012-5-14 17:35
{:soso_e132:}

作者: jiang056@163.co 时间: 2012-12-16 16:12
看看。。。。。。。。。。

作者: cjp818 时间: 2013-2-2 15:02
这都什么跟什么呀~~~~

作者: pwb7627 时间: 2013-2-6 19:40

作者: 李同 时间: 2013-2-12 10:14
支持一下

作者: miaomiao1990 时间: 2013-2-14 19:59

看看。。。。。。。。。。

作者: 赵盼 时间: 2013-2-14 21:32
好像是宏程序吧。

作者: 赵盼 时间: 2013-2-14 21:54
好像不是宏程序，这个程序出来了加工的是斜面，有几个地方不大好，第19,20,113,114.
这个程序的Z是根据L变化的。
我也不大懂你的程序，先用仿真走一遍程序。

欢迎光临 iCAx开思网 (https://www.icax.org/)