I-deas老是报告这种错,是什么原因？

Selected:
  
"Untitled1"
  
FEA Extrude8
  
*** Internal error 2424/39524 in function gm3sc/gm3scdl
  
2424/39524 - GM_CANT_DELETE_COMPONENT
  
*** Internal error in function gm3cv/gm3cvdl
  
*** - gm3scdl returned a 39524 when called by
  
*** gm3cv/gm3cvdl at position 60
  
*** Internal error in function wf3skre/delete_ghost_curve
  
*** - gm3cvdl returned a 39524 when called by
  
*** wf3skre/delete_ghost_curve at position 800
  
There is geometry used as a projection target that
  
is out of date
  
There is no valid target to project onto
  
*** Internal error 2424/39549 in function gm3cvms
  
2424/39549 - GM_CANT_GET_WF_CURVE
  
*** Internal error in function wf3gcscutil/wf3gcsc_QueryUnderlyingEntit
  
*** - gm3cvms returned a 39549 when called by
  
*** wf3gcscutil/wf3gcsc_QueryUnderlyingEntit at position 880
  
*** Internal error 2424/39549 in function gm3cvms
  
2424/39549 - GM_CANT_GET_WF_CURVE
  
*** Internal error in function wf3gcscutil/wf3gcsc_QueryUnderlyingEntit
  
*** - gm3cvms returned a 39549 when called by
  
*** wf3gcscutil/wf3gcsc_QueryUnderlyingEntit at position 880
  
*** Internal error 2424/39549 in function gm3cvms
  
2424/39549 - GM_CANT_GET_WF_CURVE
  
*** Internal error in function wf3gcscutil/wf3gcsc_QueryUnderlyingEntit
  
*** - gm3cvms returned a 39549 when called by
  
*** wf3gcscutil/wf3gcsc_QueryUnderlyingEntit at position 880
  
*** Internal error in function gm3sc/gm3scvd_Doit
  
*** at position 3521: There are no curve loops in this section
  
*** - Aborting wf3gmup2/wf3gmup2_Replay at position 1808
  
*** - Aborting wf3gmup2 at position 810
  
*** - Aborting wf3gmup at position 325
  
*** - Aborting gh3re/gh3restx at position 1065
  
*** - Aborting gh5rest/gh5rest at position 120
  
*** - Aborting MM5GH/mm5ghrp at position 280
  
Selected 1 entity
  
Selected:
  
"Untitled1"
  
FEA Extrude8
  
Replaying : Untitled1
  
Feature suppression is ON
  
Total steps to perform = 7 (out of 7)
  
Step 1 of 7 : RefGeo3
  
Substep 1 : Coordinate System (CS2) => Key-In
  
Step 2 of 7 : Extrude4
  
Step 3 of 7 : Add5 - (Step 1) (Step 2)
  
Step 4 of 7 : Extrude6
  
Step 5 of 7 : Intersect7 - (Step 3) (Step 4)
  
Step 6 of 7 : Extrude8
  
Step 7 of 7 : Cut9 - (Step 5) (Step 6)
  
*** Internal error in function gm3sc/gm3scvd_Doit
  
*** at position 3521: There are no curve loops in this section
  
*** - Aborting wf3gmup2/wf3gmup2_Replay at position 1391
  
*** - Aborting wf3gmup2 at position 810
  
*** - Aborting wf3gmup at position 325
  
*** - Aborting gh3re/gh3restx at position 1758
  
*** - Aborting gh5rest/gh5rest at position 120
  
最近干活老是出这种错。刚才在自己的电脑上随便做样东西，也出了这种错。是什么原因？还是我有不良的操作习惯？  
  
  还有什么reduntant restrictation什么的。烦死了。  
  
你们有没有遇上过这样的？多不多？

错误可真多，建议你还是重新做系统吧！

什么叫重新做系统啊？

还有什么reduntant restrictation什么的。烦死了。

  
这个可能是识别到了过约束，不是什么奇怪的东西。
  
其它的错误可就不正常了？

你的模型文件有错误，建议你将其输出成I-DEAS Archive File，然后重新开一个新的模型文件，将输出的I-DEAS Archive File（后缀是.arc）重新输入，一般情况下即可修正错误。