GPP2分割和重命名文件的方法

paul258

中英文合并多看几遍也就看懂了。
希望对有些人有用。


一，分割

Anyway, this all revolves around the [size=105%]CUT_FILE system variable.

该[size=105%]CUT_FILE系统变量正是这么做的，它减少了输出文件。

The [size=105%]CUT_FILE system variable does exactly that, it cuts the output file.

您将执行以下行添加到您的邮寄方式：

You would implement it by adding the following line to your post:

[size=105%]CUT_FILE = [size=105%]TRUE_;

[size=105%]CUT_FILE = [size=105%]TRUE_ ;

当GPP2发布引擎看到这个变量的值被设置为这个[size=105%]TRUE_，下列事件发生：

When the GPP2 posting engine sees that the value of this variable has been set to [size=105%]TRUE_ , the following events occur:

• 后跳转到[size=105%]磁带的末尾作者：beforecut：块，并执行代码中有。
  The post jumps to the [size=105%]END OF TAPE: beforecut: block, and executes the code there.
  这是您将添加代码以启动行输出任何你需要在新的文件。
  This is where you would add code to output any startup lines you'll need in the new file.
  你很可能需要添加到您的文章这个区块，因为它是不包括在标准职位。
  You will most likely need to add this block to your post, as it is not included in the standard posts.
• 切割后的G代码文件，并启动一个新的文件。
  The post cuts the g-code file and starts a new file.
• 后跳转到[size=105%]磁带的开头作者：aftercut：块，并执行代码中有。
  The post jumps to the [size=105%]BEGINNING OF TAPE: aftercut: block, and executes the code there.
  这是您将代码添加到文件中的行输出任何的结束时，您将需要在您的新文件。
  This is where you would add code to output any end of file lines you'll need in your new file.
  再次，你最有可能需要添加到您的文章这个区块，因为它是不包括在标准职位。
  Once again, you will most likely need to add this block to your post, as it is not included in the standard posts.
• 变量值的[size=105%]CUT_FILE系统重新设置为[size=105%]FALSE_。
  The value of the [size=105%]CUT_FILE system variable is set back to [size=105%]FALSE_ .

因此，如果添加[size=105%]CUT_FILE = [size=105%]TRUE_代码？

So, where to add the [size=105%]CUT_FILE = [size=105%]TRUE_ code?

那么，你要削减在刀具路径，所以你有两个选择。

Well, you want to cut at the toolpath, so you have two options.

• [size=105%]年初的[size=105%]TLPATH：块
  The [size=105%]BEGINNING OF TLPATH: block
• [size=105%]刀具路径[size=105%]会期：块
  The [size=105%]END OF TOOLPATH: block

起初，你可能认为[size=105%]刀具路径会期：块将是最好的，因为它似乎是有意义的每缩短刀具路径的文件结尾。

At first, you might think the [size=105%]END OF TOOLPATH: block would be best, as it would seem to make sense to cut the file at the end of every toolpath.

不幸的是，这将增加在您的文件非常切成末，几乎没有给你一个额外的文件，如果任何代码。

Unfortunately, this would add a cut at the very end of your file, giving you an extra file with little, if any code in it.

因此，我们将不得不[size=105%]使用TLPATH开始：块。

So we'll have to use the [size=105%]BEGINNING OF TLPATH: block.

同一类型的问题，虽然在这里存在，因为我们不希望在削减后的第一刀路文件开始，所以我们需要做一个计数器来计算刀具路径，并在第二次才开始切割toolath。

The same type of problem exists here though, as we don't want the post to cut the file at the beginning of the first toolpath, so we'll need to make a counter to count the toolpaths, and only start cutting at the second toolath.

所以，首先你需要做的就是定义一个[size=105%]序列变量叫[size=105%]TPCOUNTER来计算刀具路径。

So the first thing you'll need to do is define a [size=105%]SEQUENCING variable called [size=105%]TPCOUNTER to count the toolpaths.

你一定想一[size=105%]开始就设置变量1 [size=105%]磁带的初始这个值[size=105%]：块。

You'll want to set the initial value of this variable to 1 in the [size=105%]BEGINNING OF TAPE: block.

有一个在这个地方很多的变量初始化块的底部，所以只添加了那里。

There is a section at the bottom of this block where a lot of variable are initialized, so just add it there.

现在去你的[size=105%]开头TLPATH：块（此区块员额的标准在所有E8.5SP2P2，但需要被添加到旧文章），并添加以下行：

Now go to your [size=105%]BEGINNING OF TLPATH: block (this block is standard in all the E8.5SP2P2 posts, but will need to be added to older posts), and add the following lines:

[size=105%][size=105%]中频（TPCOUNTER“1）

[size=105%][size=105%]IF ( TPCOUNTER > [size=105%]1 )

[size=105%][size=105%]CUT_FILE = [size=105%]TRUE_;

[size=105%][size=105%]CUT_FILE = [size=105%]TRUE_ ;

[size=105%][size=105%]END_IF;

[size=105%][size=105%]END_IF ;

[size=105%]TPCOUNTER = TPCOUNTER + [size=105%]1;

[size=105%]TPCOUNTER = TPCOUNTER + [size=105%]1 ;


——www.jt258.com

paul258

WDN8081776

akk1898

qq817727

taidaing

donghai800

provider

q918970957

wskvofn2011