X3后处理

雪人2000

程序样本
%
O0101(TEST)
(DATE-07-01-09/TIME-19:39)
G21
(MCX-FILE-C:\USERS\E\DESKTOP\TEST\0.MCX)
(NC-FILE-C:\MCAMX\MILL\NC\TEST.NC)
(MATERIAL-ALUMINUM MM - 2024)
(STOCK=X100.Y100.Z20.)
(LOW-LEFT-CORNER=X-100.Y-100.Z-20.)
(UP-RIGHT-CORNER=X0.Y0.Z0.)
(T1-H127-END MILL BULL-D8.R1.-TL28.FL20.-HD63.HL60.)
(T2-H219-TAPER MILL-D8.R.5A10.-TL30.FL15.-HD28.HL70.)
( --------------------------------------------- )
( ------------------- OVERALL MAX=X8.Y12.Z123.456 )
( ------------------- OVERALL MIN=X-108.Y-53.5Z-12.345 )
G90 G10 L13 P30 R0.00
M01
N100 G90 G10 L12 P30 R0.00
G91 G0 G30 Z0
G00 G17 G40 G49 G80 G90
T1
M06
( T1 - H127 - 8. BULL ENDMILL 1. RAD   - D8. R1. )
(MAX - Z50.)
(MIN - Z-2.5)
(CUT STOCK: XY=0. Z=0.)
G00 G90 G54 X-50. Y-50. S4900 M03
G43 H127 Z50. T2
Z1.
G01 Z0. F1000.
M00(WARNING-CUTTER COMP APPLIED ON ARC MOVE)
G03 G41 D30 Y-53.5 I0. J-1.75
Z-1. I0. J3.5
Z-2. I0. J3.5
Y-46.5 Z-2.5 I0. J3.5
I0. J-3.5
G40 Y-50. I0. J-1.75
G00 Z50.
M05
S0
G91 G0 G30 Z0
G40 G49 G80
M01
N110 G90 G10 L12 P30 R0.00
G91 G0 G30 Z0
G40 G49 G80
T2
M06
( T2 - H219 - 10. FLAT ENDMILL   - D8. R.5 )
(MAX - Z123.456)
(MIN - Z-12.345)
(CUT STOCK: XY=-.123 Z=.321)
G00 G90 G54 X-108. Y11.877 S4900 M03
G43 H219 Z123.456 M08 T1
Z5.
G01 Z-12.024 F1000.
G03 X-100. Y3.877 I8. J0.
G01 X0.
G03 X8. Y11.877 I0. J8.
G00 Z123.456
(CUT STOCK: XY=0. Z=0.)
X-108. Y12.
Z5.
G01 Z-12.345
M00(WARNING-CUTTER COMP APPLIED ON ARC MOVE)
G03 G41 D30 X-100. Y4. I8. J0.
G01 X0.
G03 G40 X8. Y12. I0. J8.
G00 Z123.456
M05
S0
M09
G91 G0 G30 Z0
G40 G49 G80
M01
G90 G0 G53 X-650.0
G91 G0 G28 Y0
M30

雪人2000

雪人2000

雪人2000

雪人2000

雪人2000

斷翅

雪人2000

斷翅

雪人2000