iCAx开思网

标题: 怎么去掉Mastercam车后处理的S [打印本页]

作者: yszwx 时间: 2012-4-17 11:52
标题: 怎么去掉Mastercam车后处理的S

O0000 (T)

(TOOL - 1 OFFSET - 1)

(OD ROUGH RIGHT - 80 DEG. INSERT - CNMG 12 04 08)

N100 N100 G0 X300. Z150.

N110 G0 T0101

N120 G97 S600 M03

N130 G0 X176. Z0. M8

N1850 G71 U1. R.5

N1860 G71 P1870 Q1990 U.2 W.2 F.5

N1870 X110. S550

N1880 G3 X120. Z-5. R5.

N1890 G1 Z-35.

N1900 X136.

N1910 X140. Z-37.

N1920 Z-47.

N1930 Z-55.

N1940 X156.

N1950 X160. Z-57.

N1960 Z-133.

N1970 X172.

N1980 X176. Z-135.

N1990 Z-143.

N100 G0 Z0.

N110 M9

N120 M05

N130 T0100

N140 M01

(TOOL - 3 OFFSET - 3)

(OD FINISH RIGHT - 35 DEG. INSERT - VNMG 16 04 08)

N150 N150 G0 X250. Z250.

N160 G0 T0303

N170 G97 S550 M03

N180 G0 X110. Z0. M8

N190 G70 P1870 Q1990

N100 M9

N110 M05

N120 T0300

N130 M01

(TOOL - 23 OFFSET - 23)

(OD GROOVE RIGHT - NARROW INSERT - N151.2-185-20-5G)

N140 N140 G0 X250. Z250.

N150 G0 T2323

N160 G97 S302 M03

N170 G0 X144. Z-54.8

N180 G1 X133.318 F.1

N190 G0 X144.

N200 Z-53.267

N210 G1 X133.318

N220 X133.625 Z-53.42

N230 G0 X144.

N240 Z-51.733

N250 G1 X133.318

N260 X133.625 Z-51.887

N270 G0 X144.

N280 Z-50.2

N290 G1 X133.318

N300 X133.625 Z-50.353

N310 G0 X144.

N320 Z-52.

N330 X140.

N340 G1 Z-50.

N350 X132.918

N360 X133.218 Z-50.15

N370 G0 X140.5

N380 Z-53.

N390 X140.

N400 G1 Z-55.

N410 X132.918

N420 Z-52.8

N430 G0 X140.5

N440 M05

N450 T2300

N460 M01

(TOOL - 1 OFFSET - 1)

(OD THREAD RIGHT - SMALL INSERT - R166.0G-16MM01-100)

N470 N470 G0 X250. Z250.

N480 G0 T0101

N490 M05

N500 G0 X144. Z-32.355

N510 G76 P010029 Q0. R0.

N520 G76 X136. Z-48.5 P20000 Q8640 R0. E.8

N530 T0100

N540 M30

作者: yszwx 时间: 2012-4-17 12:32
顶顶顶顶顶顶顶

作者: hsmtool 时间: 2012-4-18 22:49

yszwx 发表于 2012-4-17 12:32
顶顶顶顶顶顶顶

顶顶顶顶顶顶顶顶顶顶

作者: hsmtool 时间: 2012-4-18 22:49
顶顶顶顶顶顶顶顶顶顶

作者: 万金婵 时间: 2012-4-18 23:09
顶顶顶顶顶顶顶顶顶顶

作者: dgasong 时间: 2012-7-20 22:35
你好，你的G71是怎么做出来的。

欢迎光临 iCAx开思网 (https://www.icax.org/)