请大狭帮忙

jycjyc

请大狭帮忙,小弟学proe不久.有关后处理问题搞不定,哪位高手能否帮忙做个后处理.或是指点一二.我用的程序格式如下单位是英制的)先谢了
%
(XXX:02/25/2007)
(XXX,03/10/2007,ADD N7 FOR CENTER POCK)
(FIXTURE FOR 781-041704-01A_HANDLE)
(PROG FOR HANDLE FIXTURE)
(THIS MACHINES 3.0X3.0 FIXTURE)
(FIXTURE SIZE: X=3.0, Y=3.0, Z=......DELRIN)
(T5=#50 .070 CAR DRILL)
(T12=1/8 90 C/SINK)
(T13=1/8 CAR FEM, .25 LOC, SET D113=0)
(T15=1/2 CAR FEM, SET D115=0)
(T24=2-56 SPIRAL CUT TAP)
(FIX-R-MILL-PCK-50-EM)
N1G0G90G40G80G49Z0M9
M1
T15M6
T1
S5500M3
G54G0X2.1463Y-2.397
G43H15Z0.1
M8
G1Z-0.09F10.
X2.397F25.
Y-2.1463
.
.
.
G1Y-0.253
X0.253
Y-2.747
X2.1463
G0Z0.1
(FIX-RF-CTR-PCK-500EM)
X1.6232Y-1.5
G1Z-0.17F10.
G3I-0.1232J0F18.
G1X1.7982
G3I-0.2982J0
G1X1.8032
G3I-0.3032J0
G0Z0.1
(FIX-F-MILL-ISLAND-50-EM)
X0.3071Y-2.0958
G1Z-0.1F10.
X0.3165Y-2.0922F18.
G3X0.3914Y-1.9243I-0.0465J0.1214
G2X2.687Y-1.5I1.1086J0.4243
X2.1004I-0.2933J0
G3X1.5Y-2.1004I-0.6004J0
G2Y-2.687I0J-0.2933
X0.3914Y-1.9243I0J1.187
G0Z0.1
(FIX-DRILL-MOUT-HOLE-07-DR)
N2G0G90G40G80G49Z0M9
M1
T5M6
T24
S7000M3
G54G0X1.9733Y-1.0267
G43H5Z0.1
M8
G98G83X1.9733Y-1.0267Z-0.4208Q0.1R0.1F18.
X1.0267
Y-1.9733
X1.9733
G80
(FIX-DRILL-MTG-HOE-OTSID-070DR)
G0X0.35Y-2.65
G98G83X0.35Y-2.65Z-0.4Q0.1R0.1F20.
Y-0.35
X2.65
Y-2.65
G80
(FIX-TAP-2-56-HOLE)
N4G0G90G40G80G49Z0M9
M1
T24M6
T24
S900M3
G54G0X1.9733Y-1.0267
G43H24Z0.1
M8
G93
G98G84X1.9733Y-1.0267Z-0.35R0.1F0.01785
X1.0267
Y-1.9733
X1.9733
G80G94
(FIX-TAP-MOUT-HOL-2-56)
G0X0.35Y-2.65
G93
G98G84X0.35Y-2.65Z-0.35R0.1F0.0179
Y-0.35
X2.65
Y-2.65
G80G94
(FIX-CHAM-ISLAND-90-CS)
N5G0G90G40G80G49Z0M9
M1
T12M6
T15
S7000M3
G54G0X0.7935Y-0.9236
G43H12Z0.1
M8
G0Z0.085
G1Z-0.015F25.
G3X0.8641Y-0.9204I0.0337J0.0369
.
.
.

X1.0068Y-1.55I0.05J0
G0Z0.1
(FIX_CENTER_POCK_125_EM)
N6G0G90G40G80G49Z0M9
M1
T13M6
S6000M3
G54G0X1.4995Y-1.5
G43H13Z0.1
M8
G1Z-0.18F15.
G2X1.4765Y-1.5306I-0.043J0.0083
G3X1.4783Y-1.5592I0.0072J-0.0139
.
.
.

G0Z0.1
G41D113X0.8468Y-1.6289
G1Z-0.18
G3X0.8317Y-1.6529I0.0044J-0.0195
I0.6683J0.1529
X0.8557Y-1.6679I0.0195J0.0045
G0G40Z0.1
G0G90G40G80G49Z0M9
G28Y0
M30
%

cliangcliang

cliangcliang

jycjyc