vericut怎样和UG连起来？

听说可以直接嵌在UG里用，高手写个步骤好吗。谢谢了

把这个文件发送到桌面快捷方式即可X:\cgtech70\windows\commands\nx5.bat

你好，我用的UG5.0和vericut6.2，按照你说的改了能进ug但加工仿真里没有vericut的图标。

编辑X:\cgtech62\windows\commands里的nx.bat文件出现如下文本，倒处第二行%UGII_ROOT_DIR%\UGII.BAT，换成UG启动程序的连接地址，如：X:\Program Files\UGS\NX 6.0\UGII\ugraf.exe即可。
  

@echo off
set CGTECH_INSTALL=d:\cgtech62

rem          CGTech, Copyright, All Rights Reserved

rem CGTech environment
call "%CGTECH_INSTALL%\windows\commands\cgtenv"

rem set CGTECH_IGNORELAST=TRUE

set CGTECH_CLASSES=%CGTECH_INSTALL%\classes
set CGTECH_PRODUCTS=%CGTECH_INSTALL%\windows
set CGTECH_LIBRARY=%CGTECH_INSTALL%\library\
if "%CGTECH_LICENSE%" == "" set CGTECH_LICENSE=%CGTECH_PRODUCTS%\license
if "%TEMP%" == "" set TEMP=C:\TEMP
if "%TMP%" == "" set TMP=C:\TEMP
if "%CGTECH_LOCALE%" == "" set CGTECH_LOCALE=english
set CGTECH_LANGUAGE=%CGTECH_CLASSES%\%CGTECH_LOCALE%
set CGTECH_HELP=%CGTECH_INSTALL%\hhelp
set CGTECH_SHOWROOM=%CGTECH_INSTALL%\showroom\
set CGTECH_SAMPLES=%CGTECH_INSTALL%\samples\
set CGTECH_TRAINING=%CGTECH_INSTALL%\training\
set CGTECH_DEFAULT_UNITS=MILLIMETER
set CGTECH_RGB_TXT=%CGTECH_PRODUCTS%\vericut\rgbhues.txt
if "%CGTECH_JRE%" == "" set CGTECH_JRE=%CGTECH_PRODUCTS%\jre


if NOT "%CGTPATH%" == "" goto cgtpathset
set path=%CGTECH_PRODUCTS%\vericut;%CGTECH_PRODUCTS%\license;%PATH%
set cgtpath=true
:cgtpathset

set waitopt=
set argstr=
if test%1==test goto cgtchkend
if %1==BATCH set waitopt=/wait
if %1==batch set waitopt=/wait
if %1==BATCHP set waitopt=/wait
if %1==batchp set waitopt=/wait
set argstr=%1
shift
:cgtgetarg
if test%1==test goto cgtchkend
if %1==BATCH set waitopt=/wait
if %1==batch set waitopt=/wait
if %1==BATCHP set waitopt=/wait
if %1==batchp set waitopt=/wait
set argstr=%argstr% %1
shift
goto cgtgetarg
:cgtchkend

if "%OS%" == "Windows_NT" set start_cmd=start "VERICUT" %waitopt%
if "%OS%" == "" set start_cmd=start %waitopt%

set UGII_VENDOR_DIR=%CGTECH_INSTALL%\windows\nx\v18
"%UGII_ROOT_DIR%\UGII.BAT"  %argstr%
:end_cgtech


修改后
set UGII_VENDOR_DIR=%CGTECH_INSTALL%\windows\ugv\v18
"X:\Program Files\UGS\NX 6.0\UGII\ugraf.exe"  %argstr%
:end_cgtech

期待回答.

期待高手讲解

原帖由 wesw168 于 2006-11-14 15:10 发表
5.4的好像不能挂在ug上,5.3的可以

听谁说的?

5.4的好像不能挂在ug上,5.3的可以

我也想知道.顶一下