上次等高过切，这次光面也过切！！！

你们是怎么了。过切！！！只会怪软件。我的就不过切。是你们不好不要怪软件。多检查就没有事了！！！！！！！！！！！！

不会就不要说UG的不好

不回那么容易过切的
做玩了 要 检查 啊

我昨天做一个铜公也中招了，四四方方的

我昨天做一个铜公也中招了

是不是要积分啊!!~~

怎样发贴啊!!!
       哪位老兄帮帮我!!~~~~~~~~~~~~

急需heidenhain320 后处理
    % G71*
N1 ; *****Task         : F:\ug-cam\prt\CECE.prt*
N2 ; *****Created By   : Administrator*
N3 ; *****Creation Date: Wed Nov 07 20:56:21 2007*
N4 ;(ToolName=D8 D=8.00 R=0.00 F=50.00 L=75.00)*
N5 G90*
N6 T  S15000 M08   *
N7 G17 G40*
N8 M03*
N9 G00 G90 X-34.1268 Y2.6416*
N10 Z20.*
N11 G01 Z-11.89 F5000*
N12 Z-12.09 F1000*
N13 X-32.4602 Y1.1509*
N14 G03 X-29.1268 Y2.6416 I-31.1268 J2.6416*
N15 G01 Y3.1416*
N16 Y25.0268*
N17 G02 X-25.0268 Y29.1268 I-25.0268 J25.0268*
N18 G01 X25.0268*
N19 G02 X29.1268 Y25.0268 I25.0268 J25.0268*
N20 G01 Y-25.0268*
N21 G02 X25.0268 Y-29.1268 I25.0268 J-25.0268*
N22 G01 X-25.0268*
N23 G02 X-29.1268 Y-25.0268 I-25.0268 J-25.0268*
N24 G01 Y3.6416*
N25 G03 X-31.1268 Y5.6416 I-31.1268 J3.6416*
N26 G01 X-33.0768 Y2.6416*
N27 G03 X-29.0768 Y2.6416 I-31.0768 J2.6416*
N28 G01 Y3.1416*
N29 Y25.0268*
N30 G02 X-25.0268 Y29.0768 I-25.0268 J25.0268*
N31 G01 X25.0268*
N32 G02 X29.0768 Y25.0268 I25.0268 J25.0268*
N33 G01 Y-25.0268*
N34 G02 X25.0268 Y-29.0768 I25.0268 J-25.0268*
N35 G01 X-25.0268*
N36 G02 X-29.0768 Y-25.0268 I-25.0268 J-25.0268*
N37 G01 Y3.6416*
N38 G03 X-31.0768 Y5.6416 I-31.0768 J3.6416*
N39 G01 X-33.0268 Y2.6416*
N40 G03 X-29.0268 Y2.6416 I-31.0268 J2.6416*
N41 G01 Y3.1416*
N42 Y25.0268*
N43 G02 X-25.0268 Y29.0268 I-25.0268 J25.0268*
N44 G01 X25.0268*
N45 G02 X29.0268 Y25.0268 I25.0268 J25.0268*
N46 G01 Y-25.0268*
N47 G02 X25.0268 Y-29.0268 I25.0268 J-25.0268*
N48 G01 X-25.0268*
N49 G02 X-29.0268 Y-25.0268 I-25.0268 J-25.0268*
N50 G01 Y3.6416*
N51 G03 X-31.0268 Y5.6416 I-31.0268 J3.6416 F5000*
N52 G01 Z-11.89*
N53 Z20.*
N54 M05*
N55 M09*
N56 ;(TOTAL Machine Time: 0.93)*
N999999 % vcp800 G71*

正常了！！有时检查过了，放上机床有时还是会有一刀的了