让每个人都成为定制程序单的高手！

惠益

在定制程序单时，最麻烦的就是一些参数的英文缩写！现在全部公开：

Typical Header Variables		[/tr]
Variable	Use
||PART_NAME||	Name file name (ELT file)
||XML_DOC_PATH||	Path (ELT file)
||XML_REP_PROG_NUMBER||	program number
||XML_REP_PROG_COMMENT||	program comment
||DATE_SDD||	Date - Day
||DATE_SMM||	Date- Month
||DATE_SYY||	Date - Year
||PART_NAME||	User Name
Typical Body Variables		[/tr]
Variable	Use
||TP_NAME||	TP Name
||TP_COMMENT||	TP Comment
||PROC_NAME||	Procedure Name (short)
||PROC_LONGNAME||	Procedure Name (long)
||PROC_UCSNAME||	Procedure -BKS
||PROC_COMMENT||	Procedure Comment
||XML_CLEAR_PLANE||	Clearance Plane
||SPIN_SPEED||	Spindle Speed
||MCH_FEED||	Machine Feed
||XML_SURF_OFF||	Surface Offset (general)
||XML_SURF_TOL||	Surface Tolerance
||XML_H_STEP||	Horizontal Step
||XML_V_STEP||	Vertical Step(general)
||XML_ELECTRODE||	Electrode Machining (Yes/No)
||XML_ELEC_SPARK_3D_GAP||	Spark Gap + 3D Orbit
||XML_ELEC_PLAN_GAP||	Orbit Planar Gap
||CYC_PECK||	Drill Cycle Peck
||CYC_DWELL||	Drill Cycle Dwell
||CYCLE_1...12||	Drill Cycle
||TOOL_NAME||	Tool Name
||TOOL_CMNT||	Tool Comment
||E_TOL_TYPE||	Tool Type (see below)
||DIAMETER_||	Tool Diameter
||TOOL_RAD||	Tool Radius
||TOOL_NUM||	Magazine Number
||TEETH_NUM||	Number of Teeth
||CLEAR_LENG||	Clear Length
||CUT_LENGTH||	Cutting Length
||XML_MIN_CLEAR_LEN||	Minimum Clear Length
||TOOL_TOTAL_LENGTH||	Total Tool Length
||CON_ANG||	Tool Conic Angle
||TOOL_ANGLE||	Tool Tip Angle
||SHANK_CON||	Spindle Conic height
||SHANK_TOT||	Shank Total height.
||SHANK_BOT||	Shank Bottom radius
||SHANK_TOP||	Shank Top radius
||HOLD_CON01||	Holder Conic height (holders 1 to 10)
||HOLD_TOT01||	Holder Total height (holders 1 to 10)
||HOLD_TOP01||	Holder Top radius (holders 1 to 10)
||HOLD_BOT01||	Holder Bottom radius (holders 1 to 10)
||X_MAX||	Maximum X
||X_MIN||	Minimum X
||Y_MAX||	Maximum Y
||Y_MIN||	Minimum Y
||Z_MAX||	Maximum Z
||Z_MIN||	Minimum Z
||AIR_TIME||	Rapid Motion Time
||FEED_TIME||	Cutting Motion Time
||TOTAL_TIME||	Air Feed Time

Notes: The variables displayed in red give the totals for the entire file when used in the Trailer.

E_TOL_TYPE values: 0 – Ball cutter

1 – Bull nose cutter 2 – Flat cutter 3 – Drill 4 – Reamer 5 – Tap 6 – Center drill 7 – Lollypop cutter 8 – Slot mill (full radius) 9 – Slot mill (sharp corner) 10 – Slot mill (corner radius) 11 – Dove mill (full radius) 12 – Dove mill (sharp corner) 13 – Dove mill (corner radius) 14 – Counter sink

Typical Trailer Variables		[/tr]
Variable	Use
||PROC_CNT||	Number of procedures (with Auto-Drill also number of tools and orientation changes
||TOOL_CNT||	Number of Tools
See also Body Variables marked in red

听雨的猫

lydsl

chenwi

he_2008

whj_my

xojian

caj0133

wzy12345678

wzy12345678