请问BOSS柱的内径由螺母外径决定还是有螺丝决定

请问BOSS柱的内径由螺母外径决定还是有螺丝决定

铜螺母外径，BOSS内径小于铜螺母外径0.15`0.2MM

螺丝外径阿

谢谢！困惑！

BOSS孔徑.當然是依螺母決定.
BOSS孔参考数据
螺牙Thread 外径D
长度L 塑胶孔径 塑胶肉厚W
直径 深度Y
M1.2*0.25 2.3 2.0/2.5/3.0/3.5 2.0 3.0/3.5/4.0/4.5 0.8
M1.2*0.25 2.5 2.0/2.5/3.0/3.5 2.2 3.0/3.5/4.0/4.5 0.8
M1.4*0.3 2.3 1.8/2.0/2.5/3.0 2.0 2.8/3.0/3.5/4.0 0.8
M1.4*0.3 2.35 2.0/2.5/3.0/4.0 2.1 3.0/3.5/4.0/5.0 0.8
M1.4*0.3 2.5 2.0/2.5/3.0/3.5 2.2 3.0/3.5/4.0/4.5 0.8
M1.4*0.3 2.7 2.0/2.5/3.0/3.5 2.3 3.0/3.5/4.0/4.5 0.8
M1.6*0.35 2.5 1.8/2.0/2.5/3.0/3.5/4.0 2.2 2.8/3.0/3.5/4.0/4.5/5.0 1.0
M1.6*0.35 2.7 2.0/2.5/3.0/3.5/4.0 2.3 3.0/3.5/4.0/4.5/5.0 1.0
M1.6*0.35 3.0 2.0/2.5/3.0/3.5/4.0 2.6 3.0/3.5/4.0/4.5/5.0 1.0
M1.7*0.35 3.0 2.0/2.5/3.0/3.5/4.0 2.6 3.0/3.5/4.0/4.5/5.0 1.2
M1.8*0.35 3.0 2.0/2.5/3.0/3.5/4.0 2.6 3.0/3.5/4.0/4.5/5.0 1.2
M2.0*0.4 3.5 2.0/2.5/3.0/4.0 3.1 2.0/3.0/4.0/5.0 1.2
M2.0*0.4 3.6 1.7/2.0/2.5/3.0/4.0/5.0 3.1 2.0/2.5/3.0/4.0/5.0/6.0 1.3
M2.5*0.45 4.2 2.0/2.5/3.0/4.0/5.0 3.6 2.5/3.0/4.0/5.0/6.0 1.2
M2.5*0.45 4.4 2.0/2.5/3.0/4.0/5.0 3.8 2.5/3.5/4.0/5.0/6.0 1.6
M2.5*0.45 4.6 2.0/2.5/3.0/4.0/5.0 4.0 2.5/3.5/4.0/5.0/6.0 1.6
M2.6*0.45 4.6 2.5/3.0/4.0/5.0 4.0 3.5/4.0/5.0/6.0 1.6
M3.0*0.5 4.4 2.5/3.0/3.5/4.0/5.0 3.8 3.5/4.0/4.5/5.0/6.0 1.6
M3.0*0.5 4.6 2.5/3.0/3.5/4.0/5.0 4.0 3.5/4.0/4.5/5.0/6.0 1.6
M3.0*0.5 5.0 2.5/3.0/4.0/5.0/6.0 4.4 3.5/4.0/5.0/6.0/7.0 1.6
M3.0*0.5 5.5 3.0/4.0/5.0/6.0 4.9 4.0/5.0/6.0/7.0 1.8
M3.5*0.6 5.0 4.0/5.0/6.0/7.0 4.4 4.0/5.0/6.0/7.0 1.6
M3.5*0.6 5.5 4.0/5.0/6.0/7.0 4.9 5.0/6.0/7.0/8.0 1.8
M4.0*0.5 5.8 4.0/5.0/5.8/6.5/7.0 5.2 5.0/6.0/6.8/7.5/8.0 1.8
M4.0*0.7 6.3 4.0/5.0/5.8/6.5/8.0 5.6 5.0/6.0/6.8/7.5/9.0 2.1
M5.0*0.8 7.1 5.0/5.8/6.5/9.5 6.4 6.0/6.8/7.5/10.5 2.6
M6.0*1.0 8.7 5.0/6.5/9.5/12.5 8.0 6.0/7.5/10.5/13.5 3.3
M8.0*1.25 10.3 5.0/6.5/9.5/12.5 9.6 6.0/7.5/10.5/13.5 4.5


荣亿精密

BOSS柱.螺絲.螺母都要考虑..相輔相成

wo ddddddddd

这个表是什么东东啊，我看不懂啊，能说说不

你是镶螺母还是自攻钉啊，自攻钉的话，根据螺丝还有就是强度，镶螺母的话有标准的，网上应该可以找到，一般是有螺母外径决定，