我装了EMX模块不能用?

我装了EMX4.0模块不能用?日期也已经改过,还是一样.

那是因為你沒有安裝好，因為本論壇不可以討論安裝的話題，所以你可以到中國模具論壇網看看

EMX40安装后(随便你安装在哪个目录.最好在PRO/E根目录下)  
假设所有文件在D:\proe2001\emx40\里面.  
将D:\proe2001\emx40\text里面的CONFIG.PRO用记事本打开.改最后一段为:  
PROTKDAT d:\proe2001\emx40\text\protk.dat  
我的整个CONFIG.PRO文件如下:  
mapkey buwprojna @MAPKEY_NAMEDefine new project;\  
mapkey(continued) @MAPKEY_LABELDefine new project;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Projectmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Projectmenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `CreateProject`;  
mapkey buwprodatanzaend @MAPKEY_NAMEModify project;\  
mapkey(continued) @MAPKEY_LABELModify project;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Projectmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Projectmenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `EditProject`;  
mapkey buwproaufb @MAPKEY_NAMEPrepare project;\  
mapkey(continued) @MAPKEY_LABELPrepare project;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Projectmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Projectmenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `PrepareProject`;  
mapkey buwwezedef @MAPKEY_NAMEDefine Moldbase Assembly;\  
mapkey(continued) @MAPKEY_LABELDefine Moldbase Assembly;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Moldbasemenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Moldbasemenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `MoldbaseDefinition`;  
mapkey buwcomp @MAPKEY_NAMEAssemble/Disassemble Components;\  
mapkey(continued) @MAPKEY_LABELAssemble/Disassemble Components;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Moldbasemenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Moldbasemenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `ComponentStatus`;  
mapkey buwcrequ @MAPKEY_NAMEDefine equipment on existing point;\  
mapkey(continued) @MAPKEY_LABELDefine equipment on existing point;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Moldbasemenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Moldbasemenu`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Equipmentmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Equipmentmenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DefineEquipment`;  
mapkey buwmodequi @MAPKEY_NAMERedefine equipment;\  
mapkey(continued) @MAPKEY_LABELRedefine equipment;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Moldbasemenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Moldbasemenu`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Equipmentmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Equipmentmenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `RedefineEquipment`;  
mapkey buwdelequi @MAPKEY_NAMEDelete equipment;\  
mapkey(continued) @MAPKEY_LABELDelete equipment;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Moldbasemenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Moldbasemenu`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Equipmentmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Equipmentmenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DeleteEquipment`;  
mapkey buwcreguide @MAPKEY_NAMEDefine guide on existing point;\  
mapkey(continued) @MAPKEY_LABELDefine guide on existing point;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Moldbasemenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Moldbasemenu`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Guidemenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Guidemenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DefineGuide`;  
mapkey buwmodguide @MAPKEY_NAMERedefine guide;\  
mapkey(continued) @MAPKEY_LABELRedefine guide;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Moldbasemenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Moldbasemenu`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Guidemenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Guidemenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `RedefineGuide`;  
mapkey buwdelguide @MAPKEY_NAMEDelete guide;\  
mapkey(continued) @MAPKEY_LABELDelete guide;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Moldbasemenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Moldbasemenu`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Guidemenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Guidemenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DeleteGuide`;  
mapkey buwspavpk @MAPKEY_NAMEDefine screw on existing point;\  
mapkey(continued) @MAPKEY_LABELDefine screw on existing point;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Screwmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Screwmenu`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Screwplacement`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Screwplacement`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DefineScrewExisting`;  
mapkey buwcrscrmse @MAPKEY_NAMEDefine screw on mousepoint;\  
mapkey(continued) @MAPKEY_LABELDefine screw on mousepoint;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Screwmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Screwmenu`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Screwplacement`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Screwplacement`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DefineScrewMouse`;  
mapkey buwscrred @MAPKEY_NAMERedefine screw;\  
mapkey(continued) @MAPKEY_LABELRedefine screw;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Screwmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Screwmenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `RedefineScrew`;  
mapkey buwschrdel @MAPKEY_NAMEDelete screw;\  
mapkey(continued) @MAPKEY_LABELDelete screw;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Screwmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Screwmenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DeleteScrew`;  
mapkey buwsavp @MAPKEY_NAMEDefine dowel pin on existing point;\  
mapkey(continued) @MAPKEY_LABELDefine dowel pin on existing point;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Pinmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Pinmenu`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Pinplacement`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Pinplacement`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DefinePinExisting`;  
mapkey buwstmouse @MAPKEY_NAMEDefine dowel pin on mousepoint;\  
mapkey(continued) @MAPKEY_LABELDefine dowel pin on mousepoint;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Pinmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Pinmenu`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Pinplacement`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Pinplacement`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DefinePinMouse`;  
mapkey buwstred @MAPKEY_NAMERedefine Dowel pin;\  
mapkey(continued) @MAPKEY_LABELRedefine Dowel pin;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Pinmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Pinmenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `RedefinePin`;  
mapkey buwstdel @MAPKEY_NAMEDelete dowel pin;\  
mapkey(continued) @MAPKEY_LABELDelete dowel pin;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Pinmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Pinmenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DeletePin`;  
mapkey buwapavp @MAPKEY_NAMEDefine ejector pin on existing point;\  
mapkey(continued) @MAPKEY_LABELDefine ejector pin on existing point;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Ejectormenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Ejectormenu`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Ejectorplacement`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Ejectorplacement`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DefineEjectorExisting`;  
mapkey buwapampp @MAPKEY_NAMEDefine ejector pin on mousepoint;\  
mapkey(continued) @MAPKEY_LABELDefine ejector pin on mousepoint;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Ejectormenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Ejectormenu`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Ejectorplacement`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Ejectorplacement`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DefineEjectorMouse`;  
mapkey buwausred @MAPKEY_NAMERedefine Ejector pin;\  
mapkey(continued) @MAPKEY_LABELRedefine Ejector pin;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Ejectormenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Ejectormenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `RedefineEjector`;  
mapkey buwausdel @MAPKEY_NAMEDelete ejector pin;\  
mapkey(continued) @MAPKEY_LABELDelete ejector pin;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Ejectormenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Ejectormenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DeleteEjector`;  
mapkey buwkueerz @MAPKEY_NAMECreate cooling bore;\  
mapkey(continued) @MAPKEY_LABELCreate cooling bore;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Coolingmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Coolingmenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DefineCooling`;  
mapkey buwkuered @MAPKEY_NAMERedefine cooling bore;\  
mapkey(continued) @MAPKEY_LABELRedefine cooling bore;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Coolingmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Coolingmenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `RedefineCooling`;  
mapkey buwkuedel @MAPKEY_NAMEDelete cooling bore;\  
mapkey(continued) @MAPKEY_LABELDelete cooling bore;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Coolingmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Coolingmenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DeleteCooling`;  
mapkey buwspavp @MAPKEY_NAMEDefine support pillar on existing point;\  
mapkey(continued) @MAPKEY_LABELDefine support pillar on existing point;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Supportmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Supportmenu`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Supportplacement`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Supportplacement`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DefineSupportExisting`;  
mapkey buwspmouse @MAPKEY_NAMEDefine support pillar on mousepoint;\  
mapkey(continued) @MAPKEY_LABELDefine support pillar on mousepoint;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Supportmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Supportmenu`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Supportplacement`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Supportplacement`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DefineSupportMouse`;  
mapkey buwsupred @MAPKEY_NAMERedefine support pillar;\  
mapkey(continued) @MAPKEY_LABELRedefine support pillar;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Supportmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Supportmenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `RedefineSupport`;  
mapkey buwsdel @MAPKEY_NAMEDelete support pillar;\  
mapkey(continued) @MAPKEY_LABELDelete support pillar;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Supportmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Supportmenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DeleteSupport`;  
mapkey buwvseae @MAPKEY_NAMEChange bom-entry;\  
mapkey(continued) @MAPKEY_LABELChange bom-entry;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Organisationmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Organisationmenu`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_BOMmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_BOMmenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `EditBOMEntry`;  
mapkey buwbomformat @MAPKEY_NAMEFormat Bill of Materials;\  
mapkey(continued) @MAPKEY_LABELFormat Bill of Materials;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Organisationmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Organisationmenu`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_BOMmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_BOMmenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `FormatBOM`;  
mapkey buwbomcheck @MAPKEY_NAMECheck BOM-Entries;\  
mapkey(continued) @MAPKEY_LABELCheck BOM-Entries;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Organisationmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Organisationmenu`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_BOMmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_BOMmenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `CheckBOMEntries`;  
mapkey buwdeflib @MAPKEY_NAMEPrepare library-component;\  
mapkey(continued) @MAPKEY_LABELPrepare library-component;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Librarymenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Librarymenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DefineLibraryComp`;  
mapkey buwbibasm @MAPKEY_NAMEAssemble library-component;\  
mapkey(continued) @MAPKEY_LABELAssemble library-component;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Librarymenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Librarymenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `AssembleLibraryComp`;  
mapkey buwsdae @MAPKEY_NAMEDefine/modify slider;\  
mapkey(continued) @MAPKEY_LABELDefine/modify slider;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Slidermenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Slidermenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DefineSlider`;  
mapkey buwdelslider @MAPKEY_NAMEDelete Slider;\  
mapkey(continued) @MAPKEY_LABELDelete Slider;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Slidermenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Slidermenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DeleteSlider`;  
mapkey buwcreatelifter @MAPKEY_NAMEDefine/Modify Lifter;\  
mapkey(continued) @MAPKEY_LABELDefine/Modify Lifter;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Liftermenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Liftermenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DefineLifter`;  
mapkey buwdellifter @MAPKEY_NAMEDelete Lifter;\  
mapkey(continued) @MAPKEY_LABELDelete Lifter;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Liftermenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Liftermenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DeleteLifter`;  
mapkey buwkliaen @MAPKEY_NAMEDefine latch lock;\  
mapkey(continued) @MAPKEY_LABELDefine latch lock;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Latchmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Latchmenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DefineLatch`;  
mapkey buwdellatch @MAPKEY_NAMEDelete latch lock;\  
mapkey(continued) @MAPKEY_LABELDelete latch lock;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Latchmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Latchmenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DeleteLatch`;  
mapkey buwwzofg @MAPKEY_NAMEDefine moldbase opening;\  
mapkey(continued) @MAPKEY_LABELDefine moldbase opening;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Simulationmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Simulationmenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DefineSimulation`;  
mapkey buwwzani @MAPKEY_NAMESimulate moldbase opening;\  
mapkey(continued) @MAPKEY_LABELSimulate moldbase opening;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Simulationmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Simulationmenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `RunSimulation`;  
mapkey buwsimstop @MAPKEY_NAMEClose moldbase opening mode;\  
mapkey(continued) @MAPKEY_LABELClose moldbase opening mode;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Simulationmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Simulationmenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `QuitSimulation`;  
mapkey buwbwdb @MAPKEY_NAMECalculate clamping forces;\  
mapkey(continued) @MAPKEY_LABELCalculate clamping forces;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Calculationmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Calculationmenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `CalculateBending`;  
mapkey buw_createhc @MAPKEY_NAMECreate Holechart;\  
mapkey(continued) @MAPKEY_LABELCreate Holechart;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Holechartmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Holechartmenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `CreateHolechart`;  
mapkey buw_delhc @MAPKEY_NAMEDelete Holechart;\  
mapkey(continued) @MAPKEY_LABELDelete Holechart;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Holechartmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Holechartmenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DeleteHolechart`;  
  
default_ext_ref_scope ALL  
set_trail_single_step NO  
native_kbd_macros NO  
open_simplified_rep_by_default NO  
show_dim_sign NO  
PROTKDAT d:\proe2001\emx40\text\protk.dat ***这就是您要更改的**  
  
再将D:\proe2001\emx40\text里面的PROTK.DAT文件用记事本打开  
name EMX 4.0-2002480  
startup dll  
exec_file d:\proe2001\emx40\i486_nt\emx40.dll  
text_dir d:\proe2001\emx40\text **粗体字即是您要更改的(记住要按您的安装目录进行更改)**  
revision 22.0  
allow_stop FALSE  
end  
  
然后在您的硬盘里建一个工作目录  
比如 :\FILE  
再将D:\proe2001\emx40\text里config.pro和config.win两个文复制到这个目录下面.  
  
然后将PROE的工作目录设置在D:\FILE  
打开PRO/E.你就可以看到EMX的图标了.  
但是不可以用.  
很简单.点取  
UTILITIES里的auxiliary applications  
出现的对话框点register.选择D:\proe2001\emx40\text里面的protk.dat  
进行注册.  
  
最后.你就可以使用伟大的EMX了. !  
EMX40安装后(随便你安装在哪个目录.最好在PRO/E根目录下)  
假设所有文件在D:\proe2001\emx40\里面.  
将D:\proe2001\emx40\text里面的CONFIG.PRO用记事本打开.改最后一段为:  
PROTKDAT d:\proe2001\emx40\text\protk.dat  
我的整个CONFIG.PRO文件如下:  
mapkey buwprojna @MAPKEY_NAMEDefine new project;\  
mapkey(continued) @MAPKEY_LABELDefine new project;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Projectmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Projectmenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `CreateProject`;  
mapkey buwprodatanzaend @MAPKEY_NAMEModify project;\  
mapkey(continued) @MAPKEY_LABELModify project;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Projectmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Projectmenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `EditProject`;  
mapkey buwproaufb @MAPKEY_NAMEPrepare project;\  
mapkey(continued) @MAPKEY_LABELPrepare project;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Projectmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Projectmenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `PrepareProject`;  
mapkey buwwezedef @MAPKEY_NAMEDefine Moldbase Assembly;\  
mapkey(continued) @MAPKEY_LABELDefine Moldbase Assembly;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Moldbasemenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Moldbasemenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `MoldbaseDefinition`;  
mapkey buwcomp @MAPKEY_NAMEAssemble/Disassemble Components;\  
mapkey(continued) @MAPKEY_LABELAssemble/Disassemble Components;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Moldbasemenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Moldbasemenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `ComponentStatus`;  
mapkey buwcrequ @MAPKEY_NAMEDefine equipment on existing point;\  
mapkey(continued) @MAPKEY_LABELDefine equipment on existing point;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Moldbasemenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Moldbasemenu`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Equipmentmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Equipmentmenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DefineEquipment`;  
mapkey buwmodequi @MAPKEY_NAMERedefine equipment;\  
mapkey(continued) @MAPKEY_LABELRedefine equipment;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Moldbasemenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Moldbasemenu`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Equipmentmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Equipmentmenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `RedefineEquipment`;  
mapkey buwdelequi @MAPKEY_NAMEDelete equipment;\  
mapkey(continued) @MAPKEY_LABELDelete equipment;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Moldbasemenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Moldbasemenu`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Equipmentmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Equipmentmenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DeleteEquipment`;  
mapkey buwcreguide @MAPKEY_NAMEDefine guide on existing point;\  
mapkey(continued) @MAPKEY_LABELDefine guide on existing point;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Moldbasemenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Moldbasemenu`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Guidemenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Guidemenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DefineGuide`;  
mapkey buwmodguide @MAPKEY_NAMERedefine guide;\  
mapkey(continued) @MAPKEY_LABELRedefine guide;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Moldbasemenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Moldbasemenu`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Guidemenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Guidemenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `RedefineGuide`;  
mapkey buwdelguide @MAPKEY_NAMEDelete guide;\  
mapkey(continued) @MAPKEY_LABELDelete guide;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Moldbasemenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Moldbasemenu`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Guidemenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Guidemenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DeleteGuide`;  
mapkey buwspavpk @MAPKEY_NAMEDefine screw on existing point;\  
mapkey(continued) @MAPKEY_LABELDefine screw on existing point;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Screwmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Screwmenu`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Screwplacement`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Screwplacement`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DefineScrewExisting`;  
mapkey buwcrscrmse @MAPKEY_NAMEDefine screw on mousepoint;\  
mapkey(continued) @MAPKEY_LABELDefine screw on mousepoint;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Screwmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Screwmenu`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Screwplacement`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Screwplacement`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DefineScrewMouse`;  
mapkey buwscrred @MAPKEY_NAMERedefine screw;\  
mapkey(continued) @MAPKEY_LABELRedefine screw;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Screwmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Screwmenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `RedefineScrew`;  
mapkey buwschrdel @MAPKEY_NAMEDelete screw;\  
mapkey(continued) @MAPKEY_LABELDelete screw;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Screwmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Screwmenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DeleteScrew`;  
mapkey buwsavp @MAPKEY_NAMEDefine dowel pin on existing point;\  
mapkey(continued) @MAPKEY_LABELDefine dowel pin on existing point;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Pinmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Pinmenu`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Pinplacement`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Pinplacement`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DefinePinExisting`;  
mapkey buwstmouse @MAPKEY_NAMEDefine dowel pin on mousepoint;\  
mapkey(continued) @MAPKEY_LABELDefine dowel pin on mousepoint;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Pinmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Pinmenu`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Pinplacement`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Pinplacement`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DefinePinMouse`;  
mapkey buwstred @MAPKEY_NAMERedefine Dowel pin;\  
mapkey(continued) @MAPKEY_LABELRedefine Dowel pin;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Pinmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Pinmenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `RedefinePin`;  
mapkey buwstdel @MAPKEY_NAMEDelete dowel pin;\  
mapkey(continued) @MAPKEY_LABELDelete dowel pin;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Pinmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Pinmenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DeletePin`;  
mapkey buwapavp @MAPKEY_NAMEDefine ejector pin on existing point;\  
mapkey(continued) @MAPKEY_LABELDefine ejector pin on existing point;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Ejectormenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Ejectormenu`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Ejectorplacement`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Ejectorplacement`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DefineEjectorExisting`;  
mapkey buwapampp @MAPKEY_NAMEDefine ejector pin on mousepoint;\  
mapkey(continued) @MAPKEY_LABELDefine ejector pin on mousepoint;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Ejectormenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Ejectormenu`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Ejectorplacement`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Ejectorplacement`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DefineEjectorMouse`;  
mapkey buwausred @MAPKEY_NAMERedefine Ejector pin;\  
mapkey(continued) @MAPKEY_LABELRedefine Ejector pin;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Ejectormenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Ejectormenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `RedefineEjector`;  
mapkey buwausdel @MAPKEY_NAMEDelete ejector pin;\  
mapkey(continued) @MAPKEY_LABELDelete ejector pin;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Ejectormenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Ejectormenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DeleteEjector`;  
mapkey buwkueerz @MAPKEY_NAMECreate cooling bore;\  
mapkey(continued) @MAPKEY_LABELCreate cooling bore;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Coolingmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Coolingmenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DefineCooling`;  
mapkey buwkuered @MAPKEY_NAMERedefine cooling bore;\  
mapkey(continued) @MAPKEY_LABELRedefine cooling bore;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Coolingmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Coolingmenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `RedefineCooling`;  
mapkey buwkuedel @MAPKEY_NAMEDelete cooling bore;\  
mapkey(continued) @MAPKEY_LABELDelete cooling bore;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Coolingmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Coolingmenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DeleteCooling`;  
mapkey buwspavp @MAPKEY_NAMEDefine support pillar on existing point;\  
mapkey(continued) @MAPKEY_LABELDefine support pillar on existing point;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Supportmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Supportmenu`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Supportplacement`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Supportplacement`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DefineSupportExisting`;  
mapkey buwspmouse @MAPKEY_NAMEDefine support pillar on mousepoint;\  
mapkey(continued) @MAPKEY_LABELDefine support pillar on mousepoint;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Supportmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Supportmenu`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Supportplacement`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Supportplacement`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DefineSupportMouse`;  
mapkey buwsupred @MAPKEY_NAMERedefine support pillar;\  
mapkey(continued) @MAPKEY_LABELRedefine support pillar;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Supportmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Supportmenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `RedefineSupport`;  
mapkey buwsdel @MAPKEY_NAMEDelete support pillar;\  
mapkey(continued) @MAPKEY_LABELDelete support pillar;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Supportmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Supportmenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DeleteSupport`;  
mapkey buwvseae @MAPKEY_NAMEChange bom-entry;\  
mapkey(continued) @MAPKEY_LABELChange bom-entry;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Organisationmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Organisationmenu`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_BOMmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_BOMmenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `EditBOMEntry`;  
mapkey buwbomformat @MAPKEY_NAMEFormat Bill of Materials;\  
mapkey(continued) @MAPKEY_LABELFormat Bill of Materials;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Organisationmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Organisationmenu`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_BOMmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_BOMmenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `FormatBOM`;  
mapkey buwbomcheck @MAPKEY_NAMECheck BOM-Entries;\  
mapkey(continued) @MAPKEY_LABELCheck BOM-Entries;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Organisationmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Organisationmenu`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_BOMmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_BOMmenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `CheckBOMEntries`;  
mapkey buwdeflib @MAPKEY_NAMEPrepare library-component;\  
mapkey(continued) @MAPKEY_LABELPrepare library-component;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Librarymenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Librarymenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DefineLibraryComp`;  
mapkey buwbibasm @MAPKEY_NAMEAssemble library-component;\  
mapkey(continued) @MAPKEY_LABELAssemble library-component;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Librarymenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Librarymenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `AssembleLibraryComp`;  
mapkey buwsdae @MAPKEY_NAMEDefine/modify slider;\  
mapkey(continued) @MAPKEY_LABELDefine/modify slider;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Slidermenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Slidermenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DefineSlider`;  
mapkey buwdelslider @MAPKEY_NAMEDelete Slider;\  
mapkey(continued) @MAPKEY_LABELDelete Slider;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Slidermenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Slidermenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DeleteSlider`;  
mapkey buwcreatelifter @MAPKEY_NAMEDefine/Modify Lifter;\  
mapkey(continued) @MAPKEY_LABELDefine/Modify Lifter;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Liftermenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Liftermenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DefineLifter`;  
mapkey buwdellifter @MAPKEY_NAMEDelete Lifter;\  
mapkey(continued) @MAPKEY_LABELDelete Lifter;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Liftermenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Liftermenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DeleteLifter`;  
mapkey buwkliaen @MAPKEY_NAMEDefine latch lock;\  
mapkey(continued) @MAPKEY_LABELDefine latch lock;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Latchmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Latchmenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DefineLatch`;  
mapkey buwdellatch @MAPKEY_NAMEDelete latch lock;\  
mapkey(continued) @MAPKEY_LABELDelete latch lock;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Latchmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Latchmenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DeleteLatch`;  
mapkey buwwzofg @MAPKEY_NAMEDefine moldbase opening;\  
mapkey(continued) @MAPKEY_LABELDefine moldbase opening;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Simulationmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Simulationmenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DefineSimulation`;  
mapkey buwwzani @MAPKEY_NAMESimulate moldbase opening;\  
mapkey(continued) @MAPKEY_LABELSimulate moldbase opening;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Simulationmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Simulationmenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `RunSimulation`;  
mapkey buwsimstop @MAPKEY_NAMEClose moldbase opening mode;\  
mapkey(continued) @MAPKEY_LABELClose moldbase opening mode;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Simulationmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Simulationmenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `QuitSimulation`;  
mapkey buwbwdb @MAPKEY_NAMECalculate clamping forces;\  
mapkey(continued) @MAPKEY_LABELCalculate clamping forces;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Calculationmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Calculationmenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `CalculateBending`;  
mapkey buw_createhc @MAPKEY_NAMECreate Holechart;\  
mapkey(continued) @MAPKEY_LABELCreate Holechart;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Holechartmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Holechartmenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `CreateHolechart`;  
mapkey buw_delhc @MAPKEY_NAMEDelete Holechart;\  
mapkey(continued) @MAPKEY_LABELDelete Holechart;\  
mapkey(continued) ~ Select `main_dlg_cur` `MenuBar1`1 `EMX_MENU40`;\  
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\  
mapkey(continued) ~ Select `main_dlg_cur` `CEMX_Holechartmenu`;\  
mapkey(continued) ~ Close `main_dlg_cur` `CEMX_Holechartmenu`;\  
mapkey(continued) ~ Activate `main_dlg_cur` `DeleteHolechart`;  
  
default_ext_ref_scope ALL  
set_trail_single_step NO  
native_kbd_macros NO  
open_simplified_rep_by_default NO  
show_dim_sign NO  
PROTKDAT d:\proe2001\emx40\text\protk.dat ***这就是您要更改的**  
  
再将D:\proe2001\emx40\text里面的PROTK.DAT文件用记事本打开  
name EMX 4.0-2002480  
startup dll  
exec_file d:\proe2001\emx40\i486_nt\emx40.dll  
text_dir d:\proe2001\emx40\text **粗体字即是您要更改的(记住要按您的安装目录进行更改)**  
revision 22.0  
allow_stop FALSE  
end  
  
然后在您的硬盘里建一个工作目录  
比如 :\FILE  
再将D:\proe2001\emx40\text里config.pro和config.win两个文复制到这个目录下面.  
  
然后将PROE的工作目录设置在D:\FILE  
打开PRO/E.你就可以看到EMX的图标了.  
但是不可以用.  
很简单.点取  
UTILITIES里的auxiliary applications  
出现的对话框点register.选择D:\proe2001\emx40\text里面的protk.dat  
进行注册.  
  
最后.你就可以使用伟大的EMX了. !

注册不了是什么问题啊,