开发FANUC的NURBS插补（g6.2）

我会用DELCAM、UG、Cimatron编G6.2，但我的系统无此功能，
G6.2需要在G5P10000(显示器右下有HPCC、 AI HPCC 或NANO HP闪烁，三者功能递增）下使用，我的可是AI HPCC！谁机床有G6.2，我用AI HPCC交换！
  
SHINRUI_YOU@126.COM
  
在你机床上试试！N0090 G05 P10000
N0100 X-14.003
N0110 G6.2 P04 K0.0 X-14.003 Y0.0 Z4.637
N0120 K0.0 X-11.748 Z4.627
N0130 K0.0 X-7.053 Z2.206
N0140 K0.0 X-2.837 Z-2.3
N0150 K.136 X1.618 Z-4.175
N0160 K.321 X3.632 Z-4.303
N0170 K.377 X6.111 Z-3.097
N0180 K.43 X9.651 Z-.34
N0190 K.444 X14.878 Z3.892
N0200 K.546 X21.868 Z6.534
N0210 K.709 X26.676 Z5.939
N0220 K.86 X28.839 Z5.398
N0230 K1.
N0240 K1.
N0250 K1.
N0260 K1.
N0270 G6.2 P04 K0.0 X28.839 Y0.0 Z5.398
N0280 K0.0 X25.546 Z6.24
N0290 K0.0 X22.123 Z6.364
N0300 K0.0 X18.85 Z5.264
N0310 K1.
N0320 K1.
N0330 K1.
N0340 K1.
N0350 G6.2 P04 K0.0 X18.85 Y0.0 Z5.264
N0360 K0.0 X20.254 Z5.721
N0370 K0.0 X21.666 Z5.975
N0380 K0.0 X23.076 Z6.039
N0390 K1.
N0400 K1.
N0410 K1.
N0420 K1.
N0430 G1 X-23.076 Y-12.5
N0440 G6.2 P04 K0.0 X23.076 Y-12.5 Z6.039
N0450 K0.0 X21.666 Z5.975
N0460 K0.0 X20.254 Z5.721
N0470 K0.0 X18.85 Z5.264
N0480 K1.
N0490 K1.
N0500 K1.
N0510 K1.
N0520 G6.2 P04 K0.0 X18.85 Y-12.5 Z5.264
N0530 K0.0 X22.123 Z6.364
N0540 K0.0 X25.546 Z6.24
N0550 K0.0 X28.839 Z5.398
N0560 K1.
N0570 K1.
N0580 K1.
N0590 K1.
N0600 G6.2 P04 K0.0 X28.839 Y-12.5 Z5.398
N0610 K0.0 X26.292 Z6.055
N0620 K0.0 X21.882 Z6.432
N0630 K0.0 X15.508 Z4.106
N0640 K.163 X10.567 Z.512
N0650 K.261 X6.672 Z-2.786
N0660 K.411 X3.235 Z-4.515
N0670 K.534 X-3.459 Z-2.832
N0680 K.575 X-7.536 Z3.67
N0690 K.641 X-13.683 Z4.757
N0700 K.935 X-14.698 Z4.616
N0710 K1.
N0720 K1.
N0730 K1.
N0740 K1.
N0750 G1 X14.698 Y-25.
N1090 Z9.106
N1100 G05 P0
M2

G5P10000
用的但是
执行到  
G6.2 P04 K0.0 X-14.003 Y0.0 Z4.637  
就出现了警报无此g代码！

你的控制器沒那個Nurbs插補的功能..況且 那個東西不見得好用.. 又貴 ..別浪費時間了..即使你有那個功能..你的曲面加工起來 不見得都漂亮..

我用AI HPCC能欲读上千句，而HPCC只能欲读180句，在AI HPCC上用NURBS可能无啥明显优点，但在HPCC可能效果会明显些

g6.2需硬件支持

Nurbs插補的功能