jeson2008 ，请进

班主你好 ：你说的导入导出是在哪里设置的啊？？？能给我细说说吗？谢了

小弟好急

原帖由 yang2000 于 2005-10-12 18:50 发表
班主你好 ：你说的导入导出是在哪里设置的啊？？？能给我细说说吗？谢了

小弟好急

就是Lead in 和Lead out这两项。
同时需要设定引导半径--lead_radius

恭喜你！问一下，这是通过改后处理而来的，还是用原来的后处理，只是改变加工参数CUT_COM打开，继存器输入1，设置了LEAD_IN,LEAD_OUT,LEAD_RIDUM后得来的，请讲一下----BY XIAMEN_GUO
%
N5 G90G17G49G80G54
N10 T1
N15 M6
N20 G0 X0. Y0. Z0.
N25 T1
N30 S200 M3
N35 G0 G43 Z3. H1
N40 X-9.575 Y24.667
N45 G1 Z-5. F200.
N50 G3 G41 X-2.575 Y17.667 I7. J0. D1
N55 G41 X-2.565 Y17.667 I1. D1
N60 G1 X24.107
N65 G2 X25.305 Y17.546 I0. J-6.
N70 X27.738 Y16.856 I-3.377 J-16.55
N75 X30.751 Y15.406 I-5.914 J-16.144
N80 X33.452 Y13.386 I-9.093 J-14.975
N85 X35.735 Y10.87 I-11.975 J-13.159
N90 X38.708 Y4.739 I-14.471 J-10.803
N95 X39.32 Y-.703 I-17.641 J-4.739
N100 X37.882 Y-7.132 I-18.201 J.694
N105 X35.04 Y-11.743 I-16.55 J7.022
N110 X32.803 Y-13.948 I-13.513 J11.466
N115 X30.233 Y-15.708 I-11.11 J13.466
N120 X25.305 Y-17.546 I-8.326 J14.801
N125 X24.107 Y-17.667 I-1.198 J5.879
N130 G1 X-29.257
N135 G2 X-33.949 Y-15.406 I0. J6.
N140 X-39.33 Y-.424 I19.325 J15.398
N145 X-33.949 Y15.406 I24.707 J.431
N150 X-29.257 Y17.667 I4.692 J-3.739
N155 G1 X-2.575
N160 G40
N165 G3 X4.425 Y24.667 I0. J7.
N170 G1 X-9.575 Y26.333
N175 Z-10.
N180 G3 G41 X-2.575 Y19.333 I7. J0. D1
N185 G41 X-2.565 Y19.333 I1. D1
N190 G1 X28.214
N195 G2 X30.598 Y18.839 I0. J-6.
N200 X33.074 Y17.544 I-7.572 J-17.481
N205 X35.93 Y15.388 I-10.352 J-16.685
N210 X38.381 Y12.721 I-13.554 J-14.919
N215 X39.745 Y10.703 I-16.297 J-12.484
N220 X42.057 Y5.04 I-17.927 J-10.621
N225 X42.64 Y-1.07 I-20.507 J-5.038
N230 X41.53 Y-6.836 I-21.05 J1.062
N235 X39.034 Y-11.82 I-19.602 J6.7
N240 X35.174 Y-16.04 I-16.621 J11.325
N245 X32.673 Y-17.785 I-12.383 J15.083
N250 X30.598 Y-18.839 I-9.656 J16.442
N255 X28.214 Y-19.333 I-2.384 J5.506
N260 G1 X-32.333
N265 G2 X-37.185 Y-16.863 I0. J6.
N270 X-42.665 Y-.338 I23.169 J16.853
N275 X-41.134 Y9.252 I28.689 J.339
N280 X-37.185 Y16.863 I27.1 J-9.231
N285 X-32.333 Y19.333 I4.852 J-3.53
N290 G1 X-2.575
N295 G40
N300 G3 X4.425 Y26.333 I0. J7.
N305 G1 X-9.575 Y28.
N310 Z-15.
N315 G3 G41 X-2.575 Y21. I7. J0. D1
N320 G41 X-2.565 Y21. I1. D1
N325 G1 X32.321
N330 G2 X35.737 Y19.932 I0. J-6.
N335 X38.176 Y17.985 I-13.149 J-18.968
N340 X40. Y16.118 I-15.879 J-17.34
N345 X43.608 Y10.619 I-18.08 J-15.798
N350 X45.627 Y4.289 I-22.198 J-10.565
N355 X45.978 Y-1.037 I-24.459 J-4.289
N360 X44.898 Y-7.313 I-24.747 J1.03
N365 X42.941 Y-11.919 I-23.362 J7.207
N370 X39.427 Y-16.75 I-20.923 J11.525
N375 X35.737 Y-19.932 I-16.876 J15.838
N380 X32.321 Y-21. I-3.416 J4.932
N385 G1 X-35.41
N390 G2 X-40.382 Y-18.359 I0. J6.
N395 X-46. Y-.159 I27.162 J18.351
N400 X-40.382 Y18.359 I32.778 J.168
N405 X-35.41 Y21. I4.972 J-3.359
N410 G1 X-2.575
N415 G40
N420 G3 X4.425 Y28. I0. J7.
N425 G1 X-9.575 Y29.667
N430 Z-20.
N435 G3 G41 X-2.575 Y22.667 I7. J0. D1
N440 G41 X-2.565 Y22.667 I1. D1
N445 G1 X36.427
N450 G2 X40.648 Y20.931 I0. J-6.
N455 X44.811 Y15.737 I-20.43 J-20.639
N460 X47.403 Y10.531 I-24.891 J-15.641
N465 X49.327 Y-.627 I-27.72 J-10.524
N470 X46.945 Y-11.666 I-29.601 J.611
N475 X44.32 Y-16.492 I-26.98 J11.546
N480 X40.648 Y-20.931 I-24.118 J16.211
N485 X36.427 Y-22.667 I-4.221 J4.264
N490 G1 X-38.487
N495 G2 X-43.551 Y-19.885 I0. J6.
N500 X-49.333 Y-.234 I31.281 J19.879
N505 X-43.551 Y19.885 I37.061 J.24
N510 X-38.487 Y22.667 I5.064 J-3.218
N515 G1 X-2.575
N520 G40
N525 G3 X4.425 Y29.667 I0. J7.
N530 G1 X-9.575 Y31.333
N535 Z-25.
N540 G3 G41 X-2.575 Y24.333 I7. J0. D1
N545 G41 X-2.565 Y24.333 I1. D1
N550 G1 X40.534
N555 G2 X45.333 Y21.935 I0. J-6.
N560 X50.661 Y11.918 I-29.277 J-21.999
N565 X50.659 Y-11.926 I-34.422 J-11.918
N570 G1 X50.659 Y-11.926 Z-25.
N575 G2 X45.333 Y-21.935 I-34.603 J11.99
N580 X40.534 Y-24.333 I-4.799 J3.602
N585 G1 X-41.564
N590 G2 X-46.701 Y-21.434 I0. J6.
N595 X-46.701 Y21.434 I35.518 J21.434
N600 X-41.564 Y24.333 I5.137 J-3.101
N605 G1 X-2.575
N610 G40
N615 G3 X4.425 Y31.333 I0. J7.
N620 G1 X-9.575 Y33.
N625 Z-30.
N630 G3 G41 X-2.575 Y26. I7. J0. D1
N635 G41 X-2.565 Y26. I1. D1
N640 G1 X44.641
N645 G2 X49.862 Y22.957 I0. J-6.
N650 X55.998 Y.383 I-39.818 J-22.945
N655 X49.886 Y-22.913 I-45.912 J-.404
N660 X44.641 Y-26. I-5.245 J2.913
N665 G1 X-44.641
N670 G2 X-49.889 Y-22.909 I0. J6.
N675 X-56. Y-.001 I39.798 J22.886
N680 X-49.889 Y22.909 I45.909 J.024
N685 X-44.641 Y26. I5.248 J-2.909
N690 G1 X-2.575
N695 G40
N700 G3 X4.425 Y33. I0. J7.
N705 G1 Z3.
N710 M5
%

[ 本帖最后由 xiamen_guo 于 2005-10-13 15:43 编辑 ]

班主你好 我是PROE-NC新手 你能给我说说什么是破衣编程 吗？？？

原帖由 yang2000 于 2005-10-13 12:36 发表
班主你好 我是PROE-NC新手 你能给我说说什么是破衣编程 吗？？？

这我也说不清楚

G2X-9.447Y20.067I8.136J-.004F1500.
G2X-6.565Y22.093I6.171J-5.714F1500.
G2X-2.813Y22.844I3.73J-8.886F1500.
G1X13.189Y22.845Z-1.5F1500.
G2X16.607Y22.236I.025J-9.765F1500.
G2X19.593Y20.331I-2.96J-7.931F1500.
G2X22.012Y14.546I-5.719J-5.79F1500.
G1X22.008Y-11.589Z-1.5F1500.
G2X19.293Y-17.653I-8.136J.003F1500.
G1X23.623Y-22.5Z-1.5F1500.
G1X27.999Y-22.5Z-1.5F1500.
G1X28.Y-22.5Z-1.5F1500.
G3X29.5Y-21.I-.001J1.501F1500.
G1X29.5Y20.999Z-1.5F1500.
G1X36.Y21.002Z-1.5F1500.
G1X36.Y21.002Z20.F1500.
G0X13.189Y22.845
G0Z1.
G1X13.189Y22.845Z-1.5F600.
G2X16.607Y22.236I.025J-9.765F1500.
G2X19.593Y20.331I-2.96J-7.931F1500.
G2X22.012Y14.546I-5.719J-5.79F1500.
G1X22.008Y-11.589Z-1.5F1500.

请问老大我的F值每行都有如何改为不再重复

是通过改变加工参数CUT_COM打开，继存器输入1，设置了LEAD_IN,LEAD_OUT,LEAD_RIDUM后得来

[fly]YANG200[/fly]



1、关于是否应该输出刀具边的问题,最好在设备上作个试切,这样不仅能够更好的消化破衣参数,而且对以后的加工更可靠!
2、不知道你的设备是否是四轴，你上传的是四轴后置，如果设备非四轴，最好更改后置中的设备类型为三轴，因为输出含B 0的程序代码
3、如果这个后置没有在实际加工中使用，那么上机前，应该编写简单的加工程序并在设备上空运行，这样会更好。——当然三轴出现问题的可能小，但你的是四轴后置，且关于第四轴的定义并不完善！！

受人以鱼，不如授人以渔！
一鼓作气，继续学习

原帖由 yang2000 于 2005-10-13 20:30 发表
是通过改变加工参数CUT_COM打开，继存器输入1，设置了LEAD_IN,LEAD_OUT,LEAD_RIDUM后得来

没错吧！要多多试一试，这样才会进步

原帖由 jeson2008 于 2005-10-13 21:41 发表
[fly]YANG200[/fly]



1、关于是否应该输出刀具边的问题,最好在设备上作个试切,这样不仅能够更好的消化破衣参数,而且对以后的加工更可靠!
...

jeson2008，说得好，受人以鱼，不如授人以渔