HYPERMILL和PROE/NC开粗刀路的比较PART在6楼

在加工是换会有改善的呀

破衣开粗基本无抬刀

原帖由 zjnblhy 于 2006-12-14 23:53 发表
破衣开粗基本无抬刀

无抬刀不代表一定有效率， 现在的高速机可以快到跳刀过程也看不到， 不提刀反而慢了.  HM就针对高价机器的。

Surfcam Velocity II RapidRough 兩把刀 D50R6, D25R1

第一把刀部份路逕

兩把刀切削模擬後

當然刀子可以由大排到小..(多排幾把刀)

部分程序
%
O1
G17G40G49G80
N1T1M6
(Tool Diameter: 50.Tool Corner: 6.)
G90G0G54X33.631Y-233.282
G43Z114.H1T2M3S2000
M8
G0Z66.875
G3X29.56Y-227.5Z66.75R5.F3000.0
G3X22.895Y-226.926Z66.75R38.952F1827.2
G3X16.23Y-227.5Z66.75R38.952
G3X12.997Y-229.548Z66.813R5.F3000.0
G3X12.159Y-233.282Z66.875R5.F439.5
G0Z114.
X53.56Y-232.941Z114.
Z66.875
G3X56.945Y-231.156Z66.813R5.
G3X58.077Y-227.5Z66.75R5.F3000.0
G3X8.259Y-216.025Z66.75R26.919F1555.4
G1X7.004Y-218.096Z66.75F3000.0
G2X1.279Y-227.5Z66.75R1013.546
G3X0.671Y-231.278Z66.813R5.
G3X2.913Y-234.38Z66.875R5.F439.5
G0Z114.
X53.471Y-232.861Z114.
Z66.875
G3X56.886Y-231.135Z66.813R5.
G3X58.082Y-227.5Z66.75R5.F3000.0
G3X56.972Y-217.355Z66.75R150.357F2572.3
G3X53.869Y-207.89Z66.75R23.026F1438.4
G3X47.066Y-200.611Z66.75R23.146F1442.2
G3X43.104Y-198.407Z66.75R23.355F1449.0
G3X38.791Y-197.008Z66.75R23.499F1453.6
G3X34.228Y-196.461Z66.75R23.586F1456.3
G3X29.646Y-196.804Z66.75R23.787F1462.7
G3X25.142Y-198.049Z66.75R23.901F1466.3
G3X20.963Y-200.141Z66.75R24.155F1474.2
G3X17.196Y-203.061Z66.75R24.295F1478.5
G3X14.068Y-206.657Z66.75R24.598F1487.8
G3X8.257Y-216.023Z66.75R572.773F2874.5
G1X7.004Y-218.096Z66.75F3000.0
G2X1.279Y-227.5Z66.75R1013.546
G3X0.671Y-231.278Z66.813R5.
G3X2.913Y-234.38Z66.875R5.F439.5
......
......
G3X92.886Y7.882Z77.875R53.084F2039.5
G1X92.824Y8.201Z77.875F3000.0
G3X86.953Y12.142Z78.R5.
G0Z114.
M5
M9
G91G28Z0
M1
N2T2M6
(Tool Diameter: 25.Tool Corner: 1.)
G90G0G54X197.063Y154.436
G43Z114.H2T1M3S3500
M8
G0Z80.375
G1Z66.875F1000.0
G3X199.597Y151.971Z66.75R2.5F3000.0
G2X204.356Y151.946Z66.75R124.34
G2X209.615Y151.62Z66.75R70.028
G2X214.792Y150.939Z66.75R84.207
G2X221.692Y149.016Z66.75R32.599
G1X223.035Y148.454Z66.75
G2X226.681Y146.28Z66.75R16.762
G1X226.99Y146.042Z66.75
X228.001Y145.229Z66.75
G2X232.171Y138.761Z66.75R13.372
G1X232.181Y138.731Z66.75
G2X232.99Y133.407Z66.75R15.006
G1X232.981Y132.787Z66.75
Y131.804Z66.75
X232.981Y130.822Z66.75
....
....
G2X-121.323Y-83.015Z87.609R16.056
G1X-121.429Y-83.148Z87.609
G2X-124.899Y-86.404Z87.609R14.357
G2X-132.493Y-88.665Z87.609R13.501
G2X-142.825Y-83.507Z87.609R13.15
G2X-145.251Y-78.588Z87.609R14.162
G2X-145.861Y-75.262Z87.609R20.602
G1X-146.006Y-73.403Z87.609
G2X-146.097Y-70.283Z87.609R56.076
G1X-146.099Y-67.85Z87.609
X-146.1Y-63.111Z87.609
X-146.1Y-58.375Z87.609
X-146.102Y-46.951Z87.609
X-146.103Y-35.528Z87.609
X-146.105Y-24.012Z87.609
X-146.106Y-12.497Z87.609
X-146.107Y-7.749Z87.609
X-146.107Y-3.001Z87.609
X-146.139Y-1.047Z87.609
G2X-146.022Y2.859Z87.609R31.325
G1X-145.822Y4.661Z87.609
X-145.7Y5.637Z87.609
X-145.696Y5.687Z87.609
G2X-144.76Y10.143Z87.609R14.065
G3X-146.189Y13.377Z87.734R2.5
G0Z114.
M5
M9
G91G28Z0
M30
%

全部程序壓縮檔附件

不用懷疑一次切那麼深..

新部门有SurfCam了， 这个一定要试.

原帖由 sinderal 于 2006-12-16 00:35 发表
第一把刀部份路逕

还是大老头的这个爽！