传输出现009 读不了刀具信息

fanuc oimc系统的，原来是可以传这样的程式的，不知道动了哪个参数,麻烦版大帮我，谢谢！！！

%
O1000
G40 G17 G49 G80 G90 G21
G5.1Q1
N1 G00 G54 X112.442 Y114.596 S3100 M03
N2 G43 H01 Z70.
N3 Z2.
N4 Z1.802
N5 G01 Z-.198 F1500.
N6 G03 X110.465 Y116.294 I-1.977 J-.302
N7 X110.456 I0.0 J-2.
N8 G01 X109.802 Y116.291 F2000.
N9 X82.184 Y116.293
N10 G03 X82.041 Y116.299 I-.143 J-1.47
N11 X81.364 Y116.135 I0.0 J-1.476
N12 X80.704 Y115.009 I.63 J-1.126
N13 X80.707 Y114.92 I1.29 J0.0
N14 G01 Y45.08
N15 G03 X80.704 Y44.986 I1.275 J-.094
N16 X81.739 Y43.731 I1.278 J0.0
N17 G01 X82.184 Y43.707
N18 X110.247 Y43.708
N19 X110.449 Y43.706
N20 Y43.817 Z-.298
N21 Y43.922 Z-.397
N22 X110.247 Y43.925
N23 X81.954 Y43.926
N24 G02 X80.921 Y45.004 I.046 J1.078
N25 X80.924 Y45.08 I1.079 J0.0
N26 G01 Y114.92
N27 G02 X80.922 Y114.984 I1.102 J.064
N28 X82.026 Y116.087 I1.104 J0.0
N29 X82.184 Y116.076 I0.0 J-1.103
N30 G01 X109.802 Y116.075
N31 X110.456 Y116.077
N32 Y115.966 Z-.496
N33 Y115.861 Z-.595
N34 X109.802 Y115.858
N35 X82.184 Y115.86
N36 G03 X82.043 Y115.871 I-.141 J-.893
N37 X81.139 Y114.967 I0.0 J-.904
N38 X81.141 Y114.92 I.904 J0.0
N39 G01 X81.14 Y45.08
N40 G03 X81.139 Y45.033 I.903 J-.047
N41 X82.043 Y44.129 I.904 J0.0
N42 X82.184 Y44.14 I0.0 J.904
N43 G01 X110.247 Y44.142
N44 X110.449 Y44.139
N45 Y44.25 Z-.694
N46 Y44.356 Z-.793
N47 X110.247 Y44.359
N48 X82.184 Y44.357
N49 G02 X82.062 Y44.346 I-.122 J.694
N50 X81.356 Y45.051 I0.0 J.705
N51 X81.357 Y45.08 I.706 J0.0
N52 G01 Y114.92
N53 G02 Y114.95 I.704 J.03
N54 X82.061 Y115.654 I.704 J0.0
N55 X82.184 Y115.643 I0.0 J-.704
N56 G01 X109.802 Y115.641
N57 X110.456 Y115.644
N58 X110.459 Y115.533 Z-.893
N59 X110.463 Y115.428 Z-.992
N60 X109.802 Y115.425
N61 X82.184 Y115.427
N62 G03 X82.089 Y115.436 I-.095 J-.506
N63 X81.574 Y114.921 I0.0 J-.515
N64 Y114.92 I.515 J0.0
N65 G01 Y45.08
N66 G03 Y45.071 I.508 J-.009
N67 X82.082 Y44.563 I.508 J0.0
N68 X82.184 Y44.573 I0.0 J.508
N69 G01 X110.247 Y44.575
N70 X110.456 Y44.572
N71 Y44.684 Z-1.091
拿这个试试

O0001把

就是昨天没事做,在调背隙,可能是动了哪个参数.之前一直没问题的

改成这样又可以了!!!!!!!

不知是哪个参在作怪!!!