【推荐】五轴加工,高级加工提问区

大哥
  
我想知道为什么通过后置处理后的程序在每一刀的开始错误的？？？

haobo_cao wrote:
大哥  
  
  我想知道为什么通过后置处理后的程序在每一刀的开始错误的？？？

  
你的文件里没操作,我在做啊

BEGIN PGM 100 MM
TOOL DEF  0 L0 R0
TOOL CALL 0 Z S0
L M126
L X60.354 Y71.232 Z-53.571 A2.043 C6.318 F9999. M3 M8
L X58.512 Y68.926 Z-53.035 A2.043 C6.318 F600.
L X-13.87 Y77.272 Z-39.633 A-7.271 C-44.21 F1000.
L X-10.512 Y74.713 Z-36.973 A-9.184 C-42.059
L X-8.393 Y71.914 Z-34.535 A-11.008 C-40.728
L X-5.774 Y65.99 Z-30.077 A-14.519 C-39.116
L X-4.191 Y59.884 Z-26.125 A-17.857 C-38.174
L X-3.113 Y53.711 Z-22.617 A-21.037 C-37.554
L X-2.318 Y47.506 Z-19.484 A-24.088 C-37.112
L X-1.7 Y41.289 Z-16.676 A-27.032 C-36.776
L X-1.439 Y38.176 Z-15.38 A-28.472 C-36.636
L X-1.203 Y35.064 Z-14.151 A-29.893 C-36.51
L X-.925 Y31.958 Z-12.998 A-31.271 C-36.338
L X-.541 Y28.858 Z-11.904 A-32.624 C-36.05
L X-.083 Y25.756 Z-10.862 A-33.966 C-35.67
L X.42 Y22.65 Z-9.871 A-35.299 C-35.221
L X.946 Y19.538 Z-8.929 A-36.627 C-34.72
L X1.551 Y16.423 Z-8.048 A-37.913 C-34.105
。
。
。
红颜色为错误的代码

对不起我看看是不是操作掉了

haobo_cao wrote:
BEGIN PGM 100 MM  
  TOOL DEF  0 L0 R0  
  TOOL CALL 0 Z S0  
  L M126  
  L X60.354 Y71.232 Z-53.571 A2.043 C6.318 F9999. M3 M8  
  L X58.512 Y68.926 Z-53.035 A2.043 C6.318 F600.  
  L X-13.87 Y77.272 Z-39.633 A-7.271 C-44.21 F1000.  
  L X-10.512 Y74.713 Z-36.973 A-9.184 C-42.059  
  L X-8.393 Y71.914 Z-34.535 A-11.008 C-40.728  
  L X-5.774 Y65.99 Z-30.077 A-14.519 C-39.116  
  L X-4.191 Y59.884 Z-26.125 A-17.857 C-38.174  
  L X-3.113 Y53.711 Z-22.617 A-21.037 C-37.554  
  L X-2.318 Y47.506 Z-19.484 A-24.088 C-37.112  
  L X-1.7 Y41.289 Z-16.676 A-27.032 C-36.776  
  L X-1.439 Y38.176 Z-15.38 A-28.472 C-36.636  
  L X-1.203 Y35.064 Z-14.151 A-29.893 C-36.51  
  L X-.925 Y31.958 Z-12.998 A-31.271 C-36.338  
  L X-.541 Y28.858 Z-11.904 A-32.624 C-36.05  
  L X-.083 Y25.756 Z-10.862 A-33.966 C-35.67  
  L X.42 Y22.65 Z-9.871 A-35.299 C-35.221  
  L X.946 Y19.538 Z-8.929 A-36.627 C-34.72  
  L X1.551 Y16.423 Z-8.048 A-37.913 C-34.105  
  。  
  。  
  。  
  红颜色为错误的代码

  
机床开始时是死角
也就是说:
  
中间矢量不能有   0,0,1
A角从+到-   中间必有 0,0,1
  
程编时应避免

谢谢您的答复！！！！
这是有操作的附件part
能告诉我怎么避免死角。
能做一个例子吗？？？
谢谢！！！

wave wrote:
   
  
  机床开始时是死角  
  也就是说:  
  
  中间矢量不能有   0,0,1  
  A角从+到-   中间必有 0,0,1  
  
  程编时应避免

老大再多给点启示

BEGIN PGM 100 MM
TOOL DEF  5 L0 R0
TOOL CALL 5 Z S4500
L M126
L X60.354 Y71.232 Z-53.571 A2.043 C6.318 F9999. M3 M8
L X58.512 Y68.926 Z-53.035 A2.043 C6.318 F600.
L X56.431 Y70.256 Z-52.689 A1.737 C4.658 F1000.
L X54.308 Y71.522 Z-52.325 A1.431 C2.996
L X52.146 Y72.722 Z-51.944 A1.124 C1.333
L X49.996 Y73.83 Z-51.558 A.824 C-.294
L X47.762 Y74.896 Z-51.149 A.517 C-1.959
L X45.493 Y75.893 Z-50.727 A.21 C-3.626L X43.194 Y76.819 Z-50.293 A-.097 C-5.294
L X40.865 Y77.673 Z-49.848 A-.405 C-6.963
L X38.508 Y78.455 Z-49.392 A-.713 C-8.633
L X36.127 Y79.164 Z-48.929 A-1.021 C-10.304
L X33.722 Y79.799 Z-48.458 A-1.329 C-11.976
L X31.296 Y80.359 Z-47.98 A-1.638 C-13.65
L X28.85 Y80.844 Z-47.497 A-1.947 C-15.325
L X26.387 Y81.254 Z-47.011 A-2.256 C-17.001
L X23.91 Y81.587 Z-46.522 A-2.565 C-18.678
L X21.421 Y81.844 Z-46.031 A-2.874 C-20.356
L X18.922 Y82.024 Z-45.54 A-3.184 C-22.035
L X16.413 Y82.127 Z-45.05 A-3.494 C-23.716
L X13.899 Y82.152 Z-44.562 A-3.804 C-25.397
L X11.439 Y82.103 Z-44.088 A-4.107 C-27.041
L X8.921 Y81.977 Z-43.609 A-4.417 C-28.724
L X6.405 Y81.774 Z-43.136 A-4.727 C-30.407
L X3.89 Y81.494 Z-42.67 A-5.037 C-32.092
L X1.385 Y81.139 Z-42.212 A-5.347 C-33.775
L X-1.117 Y80.706 Z-41.763 A-5.658 C-35.462
L X-3.603 Y80.2 Z-41.326 A-5.968 C-37.145
L X-6.088 Y79.616 Z-40.898 A-6.28 C-38.837
L X-8.544 Y78.961 Z-40.485 A-6.591 C-40.519
L X-10.978 Y78.236 Z-40.089 A-6.9 C-42.198
L X-13.441 Y77.422 Z-39.699 A-7.216 C-43.91
L X-13.87 Y77.272 Z-39.633 A-7.271 C-44.21
L X-12.075 Y75.939 Z-38.202 A-8.288 C-43.066
L X-10.512 Y74.713 Z-36.973 A-9.184 C-42.059
L X-9.175 Y72.97 Z-35.426 A-10.33 C-41.223

haobo_cao wrote:
BEGIN PGM 100 MM  
  TOOL DEF  0 L0 R0  
  TOOL CALL 0 Z S0  
  L M126  
  L X60.354 Y71.232 Z-53.571 A2.043 C6.318 F9999. M3 M8  
  L X58.512 Y68.926 Z-53.035 A2.043 C6.318 F600.  
  L X-13.87 Y77.272 Z-39.633 A-7.271 C-44.21 F1000.  
  红颜色为错误的代码

  
代码没错,只是C角从6.318突然到-44.21.机床不能走的

wave wrote:
   
  
  代码没错,只是C角从6.318突然到-44.21.机床不能走的

您是怎么做的