PROE做两平面中心基准平面

学到了，谢谢分享

{:soso_e113:}      快捷键还要+udf太麻烦了吧！直接就用快捷键多好啊！为什么不直接用快捷键，指定边的中点和一个面平行就ok。
mapkey % ~ Command `ProCmdDatumPlane` ;~ Command `ProCmdDatumPointGeneral` ;\
mapkey(continued) @PAUSE_FOR_SCREEN_PICK;~ Trigger `Odui_Dlg_01` `t1.RefsTable`2  `` ``;\
mapkey(continued) ~ Trigger `Odui_Dlg_01` `t1.RefsTable`2  `` ``;\
mapkey(continued) ~ Trigger `Odui_Dlg_01` `t1.RefsTable`2  `collector_preview_row_0` `c1`;\
mapkey(continued) ~ Trigger `Odui_Dlg_01` `t1.RefsTable`2  `` ``;\
mapkey(continued) ~ Move `Odui_Dlg_01` `Odui_Dlg_01`2 21.538462 5.731421 ;\
mapkey(continued) ~ Trigger `Odui_Dlg_01` `t1.RefsTable`2  `collector_preview_row_0` `c1`;\
mapkey(continued) ~ Trigger `Odui_Dlg_01` `t1.RefsTable`2  `` ``;\
mapkey(continued) ~ Trigger `Odui_Dlg_01` `t1.RefsTable`2  `` ``;\
mapkey(continued) ~ Input `Odui_Dlg_01` `t1.OffsetOptMnu` `0`;\
mapkey(continued) ~ Input `Odui_Dlg_01` `t1.OffsetOptMnu` `0.`;\
mapkey(continued) ~ Input `Odui_Dlg_01` `t1.OffsetOptMnu` `0.5`;\
mapkey(continued) ~ Update `Odui_Dlg_01` `t1.OffsetOptMnu` `0.5`;\
mapkey(continued) ~ Activate `Odui_Dlg_01` `t1.OffsetOptMnu`;\
mapkey(continued) ~ FocusOut `Odui_Dlg_01` `t1.OffsetOptMnu`;\
mapkey(continued) ~ Activate `Odui_Dlg_01` `stdbtn_1`;@PAUSE_FOR_SCREEN_PICK;\
mapkey(continued) ~ RButtonArm `main_dlg_cur` `PHTLeft.AssyTree` `node0`;\
mapkey(continued) ~ PopupOver `main_dlg_cur` `ActionMenu`1  `PHTLeft.AssyTree`;\
mapkey(continued) ~ Open `main_dlg_cur` `ActionMenu`;@PAUSE_FOR_SCREEN_PICK;\
mapkey(continued) ~ Close `main_dlg_cur` `ActionMenu`;~ Activate `Odui_Dlg_00` `stdbtn_1`;\
mapkey(continued) ~ Expand `main_dlg_cur` `PHTLeft.AssyTree` `node13`;

yeuogj 发表于 2013-2-5 09:03
快捷键还要+udf太麻烦了吧！直接就用快捷键多好啊！为什么不直接用快捷键，指定边的中点 ...

{:soso_e127:} 你说的只能有边的情况下做，而且边还要是对称的
如果是找基准平面和实体平面的中心基准平面，用你的快捷键是搞不出来的。

有这功能？

看看……

看看，很实用的样子

看一看

学习学习

不错，赞一个

谢谢分享