有困难找警察，NX问题得找进明版竹，NX7.5可以这样处理吗？

NX7.5可以这样处理吗？
可以输出XZ（G18)与YZ(G19)平面拟合圆弧后处理的更改，望高手赐教



最后面图片是CimatronE GPP2做的后处理，一个字爽啊！

POST默認就是可以的.....試試吧！

%
G40 G17 G90 G71
G91 G28 Z0.0
T00 M06
G00 G90 X-42.36 Y49.998 S3500 M03
G43 Z20. H00
Z2.
G01 Z0.0 F1000. M08
G18 G03 X-39.36 Z-.303 I-.005 K-15.021 F1600.
G01 X-38.61 Z-.476
X-37.86 Z-.691
G03 X-27.923 Z-10.931 I-4.499 K-14.308
G01 X-27.735 Z-11.661
G02 X-20.61 Z-24.719 I27.735 K6.66
:
:
G01 X38.64 Z-.469
G03 X42.359 Z0.0 I3.727 K-14.579
G01 Z2.
G00 Z20.
G00 X54.728 Y-42.642
Z2.
G01 Z0.0 F1000.
G19 G02 Y-39.642 Z-.303 J-.005 K-15.028 F1600.
G01 Y-38.892 Z-.476
Y-38.142 Z-.691
G02 Y-31.758 Z-4.679 J-4.498 K-14.306
G01 Y-31.489 Z-4.97
Y-31.065 Z-5.462
Y-30.642 Z-6.
G02 Y-28.767 Z-9.302 J-12.029 K-9.014
:
:
G03 Y-41.892 Z-.019 J-3.764 K-14.618
G01 Y-42.642 Z0.0
Z2.
G00 Z20.
M30
%

肯定可以啦，默认的就可以
好多外挂里的后处理改掉了G18 G19的圆输出
打开后处理的DEF文件，找到圆运动块BLOCK_TEMPLATE circular_move，加入G_plane[$mom_sys_cutcom_plane_code($mom_pos_arc_plane)]\opt

Yeager 发表于 2011-8-25 10:59
POST默認就是可以的.....試試吧！

%

谢谢YEAGER

进明 发表于 2011-8-25 11:16
肯定可以啦，默认的就可以
好多外挂里的后处理改掉了G18 G19的圆输出
打开后处理的DEF文件，找到圆运动行 ...

谢谢，进明

2楼3楼的版大你好！加入G_plane[$mom_sys_cutcom_plane_code($mom_pos_arc_plane)]\opt后仍然不起作用，请帮我看一下
处理不出G18G19是模态的问题吗？在哪里改啊？二位老大
G90 G54 X0.0 Y0.0
G0 X54.728 Y-42.642 S3500 M03
Z20.
Z2.
G1 Z0.0 F1000.
G2 Y-39.642 Z-.303 J-.005 K-15.028 F1600.
G1 Y-38.892 Z-.476
Y-38.142 Z-.691
G2 Y-31.758 Z-4.679 J-4.498 K-14.306
G1 Y-31.489 Z-4.97
Y-31.065 Z-5.462
Y-30.642 Z-6.
G2 Y-28.767 Z-9.302 J-12.029 K-9.014
G1 Y-28.58 Z-9.78
Y-28.392 Z-10.316
Y-28.205 Z-10.931
Y-28.017 Z-11.661
G3 Y-20.892 Z-24.719 J27.735 K6.66
G1 Y-20.142 Z-25.475
G3 Y-.282 Z-33.525 J19.86 K20.475
Y19.608 Z-25.447 J0.0 K28.525
G1 Y20.358 Z-24.689
Y21.108 Z-23.872
G3 Y27.483 Z-11.542 J-21.407 K18.881
G2 Y29.358 Z-7.053 J14.595 K-3.46
G1 Y29.752 Z-6.453
G2 Y37.608 Z-.682 J12.331 K-8.554
G1 Y38.358 Z-.469
G2 Y42.077 Z0.0 J3.727 K-14.579
G1 X59.727
Y41.358 Z-.017
G3 Y36.858 Z-.938 J.727 K-15.01
Y28.983 Z-7.687 J5.22 K-14.06
Y27.483 Z-11.542 J13.086 K-7.312
G2 Y21.108 Z-23.872 J-27.782 K6.551
G1 Y20.358 Z-24.689
Y19.608 Z-25.447
G2 Y-.282 Z-33.525 J-19.89 K20.447
Y-26.142 Z-17.036 J0.0 K28.525
Y-28.017 Z-11.661 J25.867 K12.038
G3 Y-28.955 Z-8.864 J-14.763 K-3.392
G1 Y-29.142 Z-8.462
G3 Y-32.142 Z-4.289 J-13.497 K-6.537
Y-38.142 Z-.691 J-10.493 K-10.698
G1 Y-38.892 Z-.476
G3 Y-41.884 Z-.019 J-3.764 K-14.617
G1 Y-42.642 Z0.0
X64.727
Y-42.632
Y-42.03 Z-.01
Y-41.429 Z-.047
Y-40.83 Z-.108
Y-40.234 Z-.192
Y-39.642 Z-.303
Y-38.892 Z-.476
Y-38.142 Z-.691
G2 Y-29.517 Z-7.74 J-4.502 K-14.311
Y-28.017 Z-11.661 J-13.199 K-7.296
G3 Y-20.892 Z-24.719 J27.735 K6.66
G1 Y-20.142 Z-25.475
G3 Y-.282 Z-33.525 J19.86 K20.475
Y19.608 Z-25.447 J0.0 K28.525
G1 Y20.358 Z-24.689
Y21.108 Z-23.872
G3 Y27.483 Z-11.542 J-21.407 K18.881
G2 Y29.733 Z-6.481 J14.597 K-3.459
Y37.608 Z-.682 J12.35 K-8.525
G1 Y38.358 Z-.469
Y39.108 Z-.298
Y39.858 Z-.166
Y40.608 Z-.072
Y41.358 Z-.017
Y42.067 Z0.0
Y42.077
X69.726
Y42.067
Y41.358 Z-.017
G3 Y36.858 Z-.938 J.727 K-15.01
Y28.983 Z-7.687 J5.22 K-14.06
Y27.483 Z-11.542 J13.086 K-7.312
G2 Y21.108 Z-23.872 J-27.782 K6.551
G1 Y20.358 Z-24.689
Y19.608 Z-25.447
G2 Y-.282 Z-33.525 J-19.89 K20.447
Y-26.142 Z-17.036 J0.0 K28.525
Y-28.017 Z-11.661 J25.867 K12.038
G3 Y-28.955 Z-8.864 J-14.763 K-3.392
G1 Y-29.142 Z-8.462
G3 Y-32.142 Z-4.289 J-13.497 K-6.537
Y-38.142 Z-.691 J-10.493 K-10.698
G1 Y-38.892 Z-.476
Y-39.482 Z-.335
Y-40.077 Z-.219
Y-40.677 Z-.127
Y-41.279 Z-.06

我把Turbo關掉就可以了，先將就吧！沒研究Turbo下怎出G18/G19.....

Yeager 发表于 2011-8-25 17:29
我把Turbo關掉就可以了，先將就吧！沒研究Turbo下怎出G18/G19.....

请问YEAGER老大，turbo在PUI里关还是在def里关？

按圖索驥囉.....

Yeager 发表于 2011-8-25 23:09
按圖索驥囉.....

谢谢，YEAGER老师的帮助，再次谢谢！！！